Yamaha AN1x Owner's Manual page 110

Pa n ( Co nt r o l # 0 1 0 )
Messag es which co ntro l the stereo panning po sitio n o f
each vo ice (fo r stereo o utput).
Setting the value to 1 2 7 po sitio ns the so und to the far
rig ht and 0 po sitio ns the so und to the far left.
Ex p r e ssi o n ( Co nt r o l # 0 1 1 )
Messag es which co ntro l into natio n expressio n o f each
vo ice during perfo rmance.
Setting the value to 1 2 7 pro duces maximum vo lume
and 0 results in vo lume o ff.
Sust a i n Sw i t ch ( Co ntr o l # 0 6 4 )
Messag es which co ntro l sustain o n/ o ff.
Setting the value between 6 4 - 1 2 7 turns the sustain
o n, between 0 - 6 3 turns the sustain o ff.
Po r ta m e nt o Sw i t ch ( Co ntr o l # 0 6 5 )
Messag es which co ntro l po rtamento o n/ o ff.
Setting the value between 6 4 -1 2 7 turns the
po rtamento o n, between 0 - 6 3 turns the po rtamento
o ff.
Ha r m o ni c Co nt e nt ( Co nt r o l # 0 7 1 )
Messag es which adjust the VCF reso nance set fo r each
vo ice.
Hig her values will result in a mo re characteristic,
reso nant so und. Depending o n the vo ice, the effective
rang e may be narro wer than the rang e available fo r
adjustment.
Re le a se Ti m e ( Co ntr o l # 0 7 2 )
Messag es which directly adjust the AEG release time
set fo r each vo ice.
A tta ck Ti m e ( Co nt r o l # 0 7 3 )
Messag es which directly adjust the AEG attack time set
fo r each vo ice.
Br i g ht ne ss ( Co nt r o l # 0 7 4 )
Messag es which directly adjust the VCF cuto ff
frequency set fo r each vo ice.
L o wer values will result in a so fter so und. Depending
o n the vo ice, the effective rang e may be narro wer than
the rang e available fo r adjustment.
Ef fe ct1 D e p t h ( Re v e r b ) ( Co nt r o l
# 0 9 1 )
Messag es which adjust the send level fo r the Reverb
effect.
Ef fe ct3 D e p t h ( Va r i a ti o n [ Cho r us] )
( Co nt r o l # 0 9 3 )
Messag es which adjust the dry/ wet balance fo r the
Cho rus Variatio n Effect.
Ef fe ct4 D e p t h ( D e la y D e p t h) ( Co nt r o l
# 0 9 4 )
Messag es which adjust the send level fo r the Delay
effect.
D a ta I ncr e m e nt ( Co nt r o l # 0 9 6 )
D e cr e m e nt ( Co nt r o l # 0 9 7 ) fo r RPN
Messag es which increase o r decrease the MSB value
o f pitch bend sensitivity.
Yo u must assig n o ne o f tho se parameters using the RPN
in the external device in advance.
The data byte is ig no red.
W hen the maximum value o r minimum value is
reached, the value will no t be incremented o r
decremented further. (Incrementing the fine tune will no t
cause the co arse tune to be incremented.)
RPN ( Re g i st e r e d Pa r a m e t e r N um b e r )
LSB ( Co nt r o l # 1 0 0 )
RPN ( Re g i st e r e d Pa r a m e t e r N um b e r )
M SB ( Co nt r o l # 1 0 1 )
Messag es which o ffset, o r add o r subtract values fro m
a vo ice' s pitch bend sensitivity.
First send the RPN MSB and RPN L SB to specify the
parameter which is to be co ntro lled. Then use Data
Increment/ Decrement to set the value o f the specified
parameter.
N o te that o nce the RPN has been set fo r a channel,
subsequent data entry will be reco g nized as the same
RPN ' s value chang e. Therefo re after yo u use the RPN ,
yo u sho uld set a N ull (7 FH, 7 FH) value to avo id an
unexpected result.
Messag es which can be received are as fo llo ws:
RPN MSB RPN LSB
00 00
00 01
00 02
7F 7F
110
PARAMETER
Pitch Bend Sensitivity
Fine Tune
Coarse
Null