Yamaha AN1x Owner's Manual page 103

8 . Set the velocity sensitivity of the VCA.
Press KN O B PARAMETER G RO UP switch [VCA], then
press CO N TRO L kno b 8 to display the Vel Sens
(Velo city Sensitivity) parameter in the L CD. T urn the
kno b to set a value near " +1 5 " to increase the
sensitivity.
9 . Adjust the cutoff frequency a nd set the
velocity sensitivity of the VCF.
Press KN O B PARAMETER G RO UP switch [VCF], then
press CO N TRO L kno b 5 o nce to display the VCF
Cuto ff parameter in the L CD. T urn the kno b to set a
value near " 7 5 " to so ften the so und.
Press CO N TRO L kno b 8 o nce to display the Vel Sens
(Velo city Sensitivity) parameter in the L CD. T urn the
kno b to set a value near " +1 5 " , to increase the
sensitivity applied to the VCF with playing streng th.
N ext, use CO N TRO L kno b 5 to further adjust the VCF
Cuto ff. Use kno b 7 to set the FEG Depth to yo ur liking ,
and use kno b 8 to further define the Vel Sens
acco rding to yo ur playing style.
NOTE
The Velocity Sensitivity setting affects the rate of change of the FEG Depth. The
FEG Depth setting determines the range of the change.
1 0 . Apply vibra to to the voice.
Press KN O B PARAMETER G RO UP switch [VCO 1 ] and
press CO N TRO L kno b 8 to display the Pmo d Depth
(Pitch Mo dulatio n Depth) parameter in the L CD. T urn
the kno b to set a value o f abo ut " +2 0 " . This applies
the vibrato effect to the vo ice when yo u play.
N ext, let's set up the vibrato to be applied by the
[MO DUL ATIO N ] wheel, in o rder to co ntro l the amo unt
o f vibrato as yo u play. Chang e the Pmo d Depth setting
back to " 0 " .
W e' ll use o ne o f the 1 6 sets in the Co ntro l Matrix to
assig n the VCO 1 Pitch Mo dulatio n Depth parameter to
the [MO DUL ATIO N ] wheel.
Set the [EDIT RO T ARY] switch to the VO ICE SCEN E
SETUP menu.
• Press Set N o [UP/ DO W N ] to display " Set 1 " in the
L CD.
• Press Param [UP/ DO W N ] to display " VCO 1
Pmo dDp" in the L CD.
• Press So urce [UP/ DO W N ] to display " A.MW " in the
L CD.
NOTE
You can also assign a Control Change number to the Source, by which to control
the Parameter. In this case the Control Change number must match the setting in
the UTILITY SETUP menu's Control Device and Control Number.
Yo u can co ntro l the vibrato o f the VCO 1 by mo ving the
[MO DUL ATIO N ] wheel. T o further define the rang e o f
vibrato co ntro l, press Depth [UP/ DO W N ] to set a
value o f " Dp+2 0 " .
W e' ll use ano ther Co ntro l Matrix set to assig n the
VCO 2 Pitch Mo dulatio n Depth parameter also to the
[MO DUL ATIO N ] wheel.
• Press Set N o [UP/ DO W N ] to display " Set 2 " in the
L CD. " Param O ff" will also be indicated.
• Press Param [UP/ DO W N ] to display " VCO 2
Pmo dDp" in the L CD.
• Press So urce [UP/ DO W N ] to display " A.MW " in the
L CD.
Yo u can co ntro l the vibrato o f the VCO 2 by mo ving the
[MO DUL ATIO N ] wheel. T o further define the rang e o f
vibrato co ntro l, press Depth [UP/ DO W N ] to set a
value o f " Dp+2 0 " .
NOTE
Try setting different Control Matrix Depth values to the VCO1 and VCO2 to hear
the effect produced.
There a re m a ny other pa ra m eters you ma y
w a nt to a djust to get just the right sound you
w a nt. W hen you're finished w ith the editing
process, perform a Voice Store opera tion to
store your crea tion. For inform a tion, see pa ge
9 8 .
103