Mitsubishi Electric LGH-15RX5 -E Instruction Manual page 101

15.2.2 Function Selection
Perform only when change is necessary with Mr. Slim indoor unit.
(Cannot be perf med with CITY MULTI control system.) or
Set the functions of each indoor unit from the remote controller as required (See Table 1 for a list of functions).
Table 1. Function List (For a detailed description of the factory settings and mode of each indoor unit, refer to the indoor unit installation manual.)
Function
Power failure automatic
ot available
recovery
Available (Wait for approximately four minutes after power is restored.)
operating a
Measuring
Set by indoor unitÕs remote controller
Indoor temperature
Remote controllerÕs internal sensor
ot Supported (factory setting)
LOSS AY connectivity Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
240 V
Power voltage
220 V, 230 V
Energy-saving cycle automatically enabled
AUTO mode
Energy-saving cycle automatically disabled
100 Hr
Filter sign 2500 Hr
o filter sign indicator
Quiet
Fan speed
Standard
High ceiling
Four directions
umber of air outlets
Three directions
Two directions
Installed options (high-
ot supported
performance filter)
Supported
o vanes
Up/down vane setting
Equipped with vanes ( o. 1 set)
Equipped with vanes ( o. 2 set)
Energy-saving air flow
Disabled
(Heating mode)
Enabled
Humidifier
ot supported
(Direct Add-on type)
Supported
OTE: If indoor unit functions were changed after installation was complete, always indicate the set contents by entering or other mark in
the appropriate check field of Table 1.
[Function selection workflow]
The following is an example of ÒRoom temperature detection positionÓ of Table 1.
(For the actual setting procedure, see [Setting procedure]
Check the function selection set contents.
1
Switch to the FU CTIO SELECTIO mode.
2
(Press and simultaneously when the remote controller is OFF.)
A B
Refrigerant address specification 00 (Outdoor unit specification)
3
Unit address number specification
4
(Buttons and operation)
C D
Registration (Press button
5
Mode number selection
6
Setting number selection
7
(Buttons and operation)
F G
Register (Press button
8
End function display (Press buttons
0
Settings
verage
Standard
High ceiling PL(H)(A)-P AA type
1
High ceiling
2
1
(Unnecessary for single refrigerant system.)
00 (Indoor unit specification)
(Specified indoor unit
.)
E Fan operation)
02 (Room temperature detection position)
3 (remote controller fixed)
.)
E
O
End?
YES
and simultaneously.)
A B
Mode number Setting number
01
01
02
02
02
03
03
03
04
04
05
05
07
07
07
08
08
08
09
09
09
10
10
11
11
11
12
12
13
13
to .)
0
Change
O
refrigerant
address and unit
address number?
Check Unit address number
Unit address number 00
1
2
1
2
These items are set for all in-
3
door units.
1
2
3
1
2
1
2
Unit address number 01 to 04 or
1
AL
2
3
1
2
3
1
2
These items are set for each
3
indoor unit.
1
2
1
2
3
1
2
1
2
YES
9
TIME SU MO TUE WED THU FRI SAT
TIMER
AFTER
F
O LY1Hr.
TEMP.
ME U
O /OFF
E
BACK DAY
MO ITOR/SET
PAR-21MAA CLOCK
G
C
Hr O
AFTER OFF
ERROR CODE
FU CTIO
FILTER
WEEKLY
SIMPLE
AUTO OFF
O /OFF
I
A
FILTER
TEST
CHECK
B
OPERATIO
CLEAR
H
D
C-101