Mitsubishi Electric FX3G User Manual page 233

FX /FX /FX /FX /FX
3S 3G 3GC 3U 3UC
FX -4DA (4-channel Analog Output)
3U
BFM number
Data to be output from channel 1 upon PLC stop
*1
#32
(Valid only if BFM#5 = H2)
Data to be output from channel 2 upon PLC stop
*1
#33
(Valid only if BFM#5 = H2)
Data to be output from channel 3 upon PLC stop
*1
#34
(Valid only if BFM#5 = H2)
Data to be output from channel 4 upon PLC stop
*1
#35
(Valid only if BFM#5 = H2)
#36, #37 Not used
#38 Upper/lower limit function setting
#39 Upper/lower limit function status
#40 Clear of upper/lower limit function status
#41 Channel-1 lower limit of upper/lower limit function
#42 Channel-2 lower limit of upper/lower limit function
#43 Channel-3 lower limit of upper/lower limit function
#44 Channel-4 lower limit of upper/lower limit function
#45 Channel-1 upper limit of upper/lower limit function
#46 Channel-2 upper limit of upper/lower limit function
#47 Channel-3 upper limit of upper/lower limit function
#48 Channel-4 upper limit of upper/lower limit function
#49 Not used
Corrective function setting by load resistance
*1
#50
(Valid only in voltage output mode)
*1
Load resistance value for channel 1 (Unit: Ω)
#51
*1 Load resistance value for channel 2 (Unit: Ω)
#52
*1 Load resistance value for channel 3 (Unit: Ω)
#53
*1
Load resistance value for channel 4 (Unit: Ω)
#54
#55 to #59 Not used
*1
Status automatic transfer function setting
#60
Error status data (BFM#29) automatic transfer-
*1
to data register specification (Valid if b0 of
#61
BFM#60 is set to ON)
Upper/lower limit function status data (BFM#39)
*1
automatic transfer-to data register specification
#62
(Valid if b1 of BFM#60 is set to ON)
Disconnection detection status data (BFM#28)
*1
automatic transfer-to data register specification
#63
(Valid if b2 of BFM#60 is set to ON)
#64 to #79 Not used
*1. If power failure occurs, the EEPROM will retain the data.
*2. Specify the use of the upper/lower limit function for each channel setting one of hex code 0 to 2 in
each digit.
*3. Use b0 to b1.
*4. Specify the use of the corrective function by load resistance for each channel setting a hex code 0 or
1 in each digit.
*5. Use b0 to b2.
PLC User's Manual - Analog Control Edition
Description Setting range Initial value
Depending on the
K0
mode used
Depending on the
K0
mode used
Depending on the
K0
mode used
Depending on the
K0
mode used
- -
*2 H0000
- H0000
*3 H0000
K-32640
K-32640
Depending on the
mode used
K-32640
K-32640
K32640
K32640
Depending on the
mode used
K32640
K32640
- -
*4 H0000
K1000 to K30000 K30000
K1000 to K30000 K30000
K1000 to K30000 K30000
K1000 to K30000 K30000
- -
*5 K0
K200
K0 to 7999
(BFM#61, #62 and
K201
#63 must have
different values.)
K202
- -
5 Buffer Memory (BFM)
5.3 Buffer Memory List (BFM)
Data type Reference
Decimal
Decimal
Subsection
5.4.12
Decimal
Decimal
- -
Hexadeci- Subsection
mal 5.4.13
Hexadeci- Subsection
mal 5.4.14
Hexadeci- Subsection
mal 5.4.15
Decimal
Decimal
Subsection
5.4.16
Decimal
Decimal
Decimal
Decimal
Subsection
5.4.16
Decimal
Decimal
- -
Hexadeci- Subsection
mal 5.4.17
Decimal
Decimal
Subsection
5.4.17
Decimal
Decimal
- -
Subsection
Decimal
5.4.18
Subsection
Decimal
5.4.19
Subsection
Decimal
5.4.20
Subsection
Decimal
5.4.21
- -
E-19
A
B
C
D
E
F
G
H
I
J