Table of Contents
Advertisement
Inventory
the following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
if any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTIcE: if you cannot find an item on this list,
carefully check around/inside the machine and
packaging materials. often, these items get lost in
packaging materials while unpacking or they are
pre-installed at the factory.
Main components (figure 9)
A. 6" three-Jaw Chuck w/2-piece Jaws ......... 1
b. steady rest ................................................ 1
c. Follow rest ................................................. 1
D. Quick-Change tool post ............................ 1
E. Backsplash ................................................. 1
base components (figure 10)
f.
Cabinets (Left & right) ............................... 2
G. Front panel Brackets (Left & right) ............ 2
H. Front panel ................................................. 1
I.
Chip tray .................................................... 1
Loose components (figure 11)
J.
8" Four-Jaw universal Chuck ..................... 1
K. 10" Faceplate .............................................. 1
L. Bottle for oil ............................................... 1
M
tool Box...................................................... 1
N. 3- & 4-Jaw Chuck, spindle Wrench ...... 1 ea
O. Change gear set ....................................... 1
—Change gear (30-tooth).......................... 1
—Change gear (54-tooth) .......................... 1
—Change gear (57-tooth) .......................... 1
—Change gear (60-tooth, 1-installed) ....... 2
—gear (56-tooth) ....................................... 1
—gear (63-tooth) ....................................... 1
—gear (66-tooth) ....................................... 1
—gear (69-tooth) ....................................... 1
—gear (78-tooth) ....................................... 1
—gear (120/127-tooth, installed) ................ 1
p.
Quick-Change tool holder ......................... 1
Q. tapered spindle sleeve Mt#5-#3 .............. 1
R. Arbor B16 to Mt#3 ..................................... 1
S. standard dead Center Mt#3 ..................... 1
T.
Carbide-tipped dead Center Mt#3 ........... 1
U. Live Center Mt#3 ....................................... 1
Model G0750G (Mfg. Since 11/12)
v.
hex Wrenches 2, 4, 5, 6, 8, 10 mm....... 1 ea
W. Wrenches 9/11, 10/12, 12/14, 17/19 mm 1 ea
X. handwheel handles ................................... 2
y.
drill Chuck B16 1.5-13mm .......................... 1
z. Cabinet Base Fasteners:
—hex Bolts M12-1.75 x 40 ......................... 6
—Flat Washers 12mm ................................ 6
—phillips head screws M6-1 x 10 ........... 12
—Cap screws M6-1 x 10 ........................... 4
—hex nuts M6-1 ........................................ 4
—Flat Washers 6mm ............................... 12
AA. drill Chuck Key ........................................... 1
Ab. phillips & standard screwdrivers #2 ..... 1 ea
Ac. spider screws ............................................ 4
AD. Camlock studs (6 installed) ....................... 6
AE. Cap screw M6-1 x 14 (6 installed) ............. 6
Qty.
Qty.
(Left)
figure 10. Base components.
J
p
r
Q
AE
figure 11. packaged components.
B
A
C
figure 9. Main components.
(right)
F
h
i
L
K
o
V
u
t
s
Ad
AB
AC
d
E
g
M
n
X
W
y
z
AA
-17-
Advertisement
Table of Contents
