Functional Description; Installing Or Removing Battery Cartridge; Overload Protection; Overheat Protection - Makita DCU602 Instruction Manual

Installing or removing the carrier
Optional accessory
Installing the carrier
1.
Take out the carrier from the box, and attach the
side rails and front rail to the base frame.
► Fig.8
2. Tighten 6 thumb nuts together with springs and
washers to fix the rails.
► Fig.9: 1. Thumb nut 2. Spring 3. Washer
3. Place the carrier on the dump unit.
Insert the bolt from the top. Attach the flat washer and
spring washer in order to the bolt, and then tighten the
nut from the bottom. Tighten the rest of the bolts and
nuts in the same way.
► Fig.10: 1. Bolt 2. Flat washer 3. Spring washer
4. Nut
Removing the carrier
To remove the carrier, perform the installation proce-
dure in reverse.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before adjusting or checking function on the
machine.
Installing or removing battery
cartridge
CAUTION:
Always switch off the machine and
lock the brake lever before installing or removing
of the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION:
Do not use the high-temperature
battery cartridge. When the high-temperature bat-
tery cartridge is used, the machine stops automati-
cally before a short beep sound is emitted, and may
cause an injury.
CAUTION:
Be careful not to pinch your fin-
gers when opening or closing the battery cover.
NOTICE:
Make sure that the cover of the battery
box is closed securely before use. Otherwise, mud,
dirt, or water may cause damage to the product or the
battery cartridge.
Installing the battery cartridge
1. Pull up the lock lever, and then open the cover of
the battery box.
► Fig.11: 1. Cover 2. Lock lever
2.
Align the tongue on the battery cartridge with the
slot on the battery box, and then slide the cartridge until
it locks in place with a little click.
► Fig.12: 1. Battery cartridge
3. Insert the lock key in the place shown in the figure
as far as it will go, and turn it clockwise.
► Fig.13: 1. Lock key
NOTE: To turn the lock key, insert the lock key
completely.
4. Close the cover of the battery box.
► Fig.14: 1. Cover
Removing the battery cartridge
1. Pull up the lock lever, and then open the cover of
the battery box.
2. Pull out the battery cartridge from the battery box
while sliding the button on the front of the cartridge.
► Fig.15: 1. Button
3.
Turn the lock key counterclockwise, and pull it out.
4. Close the cover of the battery box.
Machine / battery protection system
The machine is equipped with a machine/battery
protection system. This system automatically cuts off
power to the motor to extend machine and battery life.
The machine will automatically stop during operation
if the machine or battery cartridge is under one of the
following conditions.
A short beep sound or long beep sound is emitted
before the machine stops automatically. The battery
indicators and lamps on the control panel blink while the
beep sound is emitted.
NOTE: To cancel the beep sound, release the switch
trigger and pull the brake lever.

Overload protection

When the machine/battery is operated in a manner
that causes it to draw an abnormally high current,
the machine automatically stops and the main power
lamp blinks in green. In this situation, turn the machine
off and stop the application that caused the machine
to become overloaded such as reducing the loaded
objects. Then turn the machine on to restart.

Overheat protection

When the machine is overheated, the machine stops
automatically and the main power lamp lights up in red.
In this case, let the machine and battery cool before
turning the machine on again.
23 ENGLISH