Functional Description; Installing Or Removing Battery Cartridge - Makita DCU603 Instruction Manual

5. Securely tighten 4 bolts which were temporarily
tightened in step 3.
Removing the bucket
To remove the bucket, perform the installation proce-
dure in reverse.
Installing or removing the carrier
Optional accessory
Installing the carrier
1. Take out the carrier from the box, and attach the
side rails and front rail to the base frame.
► Fig.19
2. Tighten 6 thumb nuts together with springs and
washers to fix the rails.
► Fig.20: 1. Thumb nut 2. Spring 3. Washer
3. Place the carrier on the dump unit.
Insert the bolt from the top. Attach the flat washer and
spring washer in order to the bolt, and then tighten the
nut from the bottom. Tighten the rest of the bolts and
nuts in the same way.
► Fig.21: 1. Bolt 2. Flat washer 3. Spring washer
4. Nut
Removing the carrier
To remove the carrier, perform the installation proce-
dure in reverse.
Installing or removing the flat
bucket
Optional accessory
Installing the flat bucket
1. Take out the flat bucket and holding frames from
the box.
► Fig.22: 1. Flat bucket 2. Holding frame
2.
Assemble the holding frames by tightening
12 bolts.
► Fig.23: 1. Bolt
3. Remove the cord cover located in the lower right
corner on the rear of the machine.
► Fig.24: 1. Cord cover
4. Place the holding frames on the base unit, and
then temporarily tighten 2 bolts at the rear of the
machine. Tighten the rest of 4 bolts securely, and then
tighten 2 bolts at the rear of the machine securely.
► Fig.25: 1. Bolt (front) 2. Bolt (rear)
5. Attach the cord cover.
► Fig.26: 1. Cord cover
6. Hold the long sides of the flat bucket with two
people as shown in the figure, and mount the flat bucket
to the holding frames.
► Fig.27
Removing the flat bucket
To remove the flat bucket, perform the installation pro-
cedure in reverse.
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION:
Always switch off the machine and
lock the brake lever before installing or removing
of the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION:
Do not use the high-temperature
battery cartridge. When the high-temperature bat-
tery cartridge is used, the machine stops automati-
cally before a short beep sound is emitted, and may
cause an injury.
CAUTION:
Be careful not to pinch your fin-
gers when opening or closing the battery cover.
NOTICE:
Make sure that the cover of the battery
box is closed securely before use. Otherwise, mud,
dirt, or water may cause damage to the product or the
battery cartridge.
Installing the battery cartridge
1. Pull up the lock lever, and then open the cover of
the battery box.
► Fig.28: 1. Cover 2. Lock lever
2. Align the tongue on the battery cartridge with the
slot on the battery box, and then slide the cartridge until
it locks in place with a little click.
► Fig.29: 1. Battery cartridge
3. Insert the lock key in the place shown in the figure
as far as it will go, and turn it clockwise.
► Fig.30: 1. Lock key
NOTE: To turn the lock key, insert the lock key
completely.
4. Close the cover of the battery box.
► Fig.31: 1. Cover
Removing the battery cartridge
1.
Pull up the lock lever, and then open the cover of
the battery box.
26 ENGLISH