NETWORK TOPOLOGY OVERVIEW MANAGEMENT FOR IVD ... 2 PORT CONNECTION FOR MANAGEMENT ... 2 CONFIGURATION BY USING TERMINAL EMULATOR SOFTWARE ... 2 How to Login with a Terminal Emulator Software ... 2 How to Login with Telnet...
Page 3
How to Connect to DSL Module...10 How to Monitor DSL Status...11 How to Enable/Disable a DSL Port...11 How to Read DSL Training Rate...11 How to Change ADSL Line Profile ...11 ...
Page 4
How to Set MGCP Wildcarded End Point ID Setting ...21 How to Set Phone Number...21 How to Set Codec Setting ...22 How to Set Gain Control Setting...22 ...
This quick start guide will provide basic configuration for accessing Internet with VigorAccess IVD. Above diagram shows the basic network topology (example) among master device, slave device, MDF, CPE (ATU-R) router, user’s computer, and phone. One thing is important – always set the VPI/VCI value for the CPE the same as the ones configured in master and slave IVD device.
If users want to configure or monitor the devices, there are some methods provided here. The MGN port on the master device allows you to make control remotely; yet the Console port on the master/slave device only allows you to make control locally. Note: If you are not used to configure the settings with terminal emulator software or Telnet commands, you can use EMS (SNMP-based) software to manage these devices.
How to Login to DSL Module for Managing IVD Slave Slave device have DSL/VoIP modules installed. The DSL module plays the core role for aggregating all ATM traffic coming from DSL ports to the uplink Ethernet interface, and vice versa. Through the master controller in the master device, administrator can login to the DSL module inside slave device for managing IVD.
How to Check the Version Information To display the basic information of the controller inside the master device Login through terminal emulator software. Type the following command - Admin > system basic To display the IVD module information inside slave device Login the specified IVD slave module.
How to Save the Configuration To save the configuration for the controller Type the following command to save the configuration. Admin>commit (Master) IVD>commit (IVD slave) Note – For VoIP functions, users need to activate it by manual as following command. IVD/voip>config activate Quick Start Guide for VigorAccess CPSwVersion...
To use Telnet for managing Master/Slave device, refer to the following sections. Default IP Settings for Master Device 1. The default IP address of Outband (MGN port): 172.16.1.1/255.255.255.0) 2. IP address for Inband (UPLINK port): 0.0.0.0 (disable) How to Change Master IP Setting Changing master IP address setting (for management) is allowed to suit environment requirement.
How to Set G5 and G6 as UPLINK Interface For the environment with available Fiber connection, the UP-G1/UP-G2 connector in Master device is used as the channel to access Internet. For such condition, you can connect slave devices from G1 to G6. However for the environment without available Fiber connection, G5 and/or G6 in Master device...
– – Here provides some general and common commands used in IVD for users to configure the IVD Master. How to configure Inband IP Address Users can use the following commands to configure the inband IP address for the UP-LINK interface or inband management.
Admin/network> route -a <TargetIP> <NetMask> <GatewayIP> Admin/network> route -e <RtIdx> <TargetIP> <NetMask> <GatewayIP> Admin/network> route -d <RtIdx> Admin/network> route -D How to configure NTP and Time Users can use the following commands to configure the NTP server IP , the polling interval, time zone and the daylight saves time.
How to Upgrade Firmware Users can use the following commands to upgrade new firmware. Make sure you have prepared a TFTP server on a host and put the firmware (ivd.all for example) in the right directory of the TFTP server Command Admin>...
Here provides some general and common commands used in IVD for users to configure the IVD DSL Module. Note: Please refer to the Command Line Interface manual for getting more commands that IVD supports. Contact your dealer for advanced information. How to Monitor DSL Status Users can use the following command to check the status for specified DSL port.
How to Change ADSL Line Rate Users can use the following command to change the ADSL Line Rate for specified DSL port. The commands are listed as below. Command $modify adsl line intf ifname dsl-* disable $modify adsl line profile ifname dsl-* atucintlmaxtxrate 0x7e0000 $modify adsl line intf ifname dsl-* enable...
How to Change Management IP Address for Existing Ethernet Port Users can use the following command to change management IP address for existing uplink Ethernet port. The commands are listed as below. Command $ipconfig <ip> <mask> How to Create more VC/EOA/Bridge Users can use the following command to create more VC/EOA/Bridge.
How to Filter MAC Address by Port Users can use the following command to filter MAC address by port. The commands are listed as below. Command $create acl port macentry portId <bridge-port-id> macaddr 00:00:00:01:02:03 $create acl port macentry portId <bridge-port-id> macaddr 00:00:00:01:02:04 How to Deny MAC Address Globally Users can use the following command to deny MAC Address globally.
$modify stp info enable $modify stp port info portid <bridge-port-id> enable $get stp port info portid <bridge-port-id> How to Enable IGMP Snooping Users can use the following command to enable IGMP snooping. The commands are listed as below. Be aware that IGMP Snooping is the Factory Default Setting. Command $create filter rule entry ruleid <id>...
How to Upgrade Full Image Remotely Users can use the following command to remotely upgrade full image. Make sure you have prepared TFTP server. The commands are listed as below. Command (Master) Type command as below – -Admin> system upgrade <tftp server ip> <F/W file name>...
Wizard Commands In addition to the primitive commands described as above. Several wizard commands are provided which is used easily. Type wizard to see the command syntax. Command $ wizard <List of Wizard Commands> --------------------------------------------------------------- $dsl show [fast] $alarm show $pvc show $pvc create <dsl: 1~24>...
Here provides commands used in IVD for users to configure VoIP features. How to Reboot - Help IVD/system> reboot ? - Reboot the system IVD/system> reboot - Reboot the system with keeping some important configuration IVD/system> reboot keep - Reboot the system with factory default configuration IVD/system>...
How to Set SIP local port Setting - Help IVD/voip/sip> localport ? - Display the setting IVD/voip/sip> localport –s - Edit sip local port number IVD/voip/sip> localport <Port> Port 1…65535 (Default is 5060) How to Set SIP Proxy Server Setting - Help IVD/voip/sip>...
How to Set MGCP Local Port Setting - Display the setting IVD/voip/mgcp> localport -s - Edit the local port number for MGCP protocol IVD/voip/mgcp> localport <Port> Port Assign a UDP port number to Call Agent server. 1...65535 (Default is 2427) How to Set MGCP Call Agent Setting - Help IVD/voip/mgcp>...
How to Set MGCP Wildcarded End Point ID Setting - Help IVD/voip/mgcp> wildrsip ? - Display the setting IVD/voip/mgcp> wildrsip -s - Setting the wildcarded RSIP action IVD/voip/mgcp> wildrsip <Active> Active How to Set Phone Number - Help IVD/voip/sip> phonenumber ? - Display the setting IVD/voip/sip>...
How to Set Codec Setting - Help IVD/voip/sip> codec ? - Display the setting IVD/voip/sip> codec -s - Edit prefect codec, codec rate and VAD for the port# IVD/voip/sip> codec <Port> <PreferCodec> <CodecRate> <VAD> - Edit single codec for the port# IVD/voip/sip>...
How to Set DTMF Relay Setting - Help IVD/voip/sip> dtmf_relay ? - Display the setting IVD/voip/sip> dtmf_relay -s - Edit dtmf relay mode for the port# IVD/voip/sip> dtmf_relay <Port> <Mode> - Edit dtmf relay mode and SIP INFO mode for the port# IVD/voip/sip>...
Note - It is very important to provide Group function for voice service in company. Customers can simultaneously call a same phone number to in the first port of a group from Internet, IVD will ring all available ports belonged to this group to provide voice service at the same time.
Memo Users can add some descriptions for each number. (Default is none) How to Set Advanced Speed Dial Setting - Help IVD/voip/sip> advspdial ? - Display the setting IVD/voip/sip> advspdial –s - Add prefix, strip length, append number, destination and memo for the entry IVD/voip/sip>...
How to Set Region Code for Tone Setting - Help IVD/voip/tone> region ? - Display the setting IVD/voip/tone> region -s - choose the region for CPT setting IVD/voip/tone> region <Region Number> Region Number Quick Start Guide for VigorAccess Select one country area for using VoIP feature. There is one option User Defined for proprietary setting.
How to Set User Defined Busy Tone Setting - Help IVD/voip/tone/user_defined> busy ? - Display the setting IVD/voip/tone/user_defined> busy -s - Edit frequency and cadence for busy tone IVD/voip/tone/user_defined> busy <Lowfreq> <Highfreq> <Ton1> <Toff1> <Ton2> <Toff2> Lowfreq Highfreq Ton1(msec) TOff1(msec) Ton2(msec) Toff2(msec) How to Set User Defined Ringing Tone Setting...
How to Set User Defined Congestion Tone Setting - Help IVD/voip/tone/user_defined> congestion ? - Display the setting IVD/voip/tone/user_defined> congestion -s - Edit frequency and cadence for congestion tone IVD/voip/tone/user_defined> congestion <Lowfreq> <Highfreq> <Ton1> <Toff1> <Ton2> <Toff2> Lowfreq Highfreq Ton1(msec) TOff1(msec) Ton2(msec) Toff2(msec) How to Set Caller ID Type Setting...
How to Set VoIP RTP Port Setting - Help IVD/voip/misc> rtp_port ? - Display the setting IVD/voip/misc> rtp_port -s - Edit the rtp starting port IVD/voip/misc> rtp_port <Port number> Port number Assign a starting port number in RTP protocol packet. 1…65535.
How to Set T.38 Redundancy Number Setting - Help IVD/voip/misc> t38redundancy ? - Display the setting IVD/voip/misc> t38redundancy -s - Edit the T.38 redundancy number IVD/voip/misc> t38redundancy <Number> Assign a redundancy number in T.38 protocol. It means how many payloads Number to be attached in the tail of packet.
How to Set NAT Traversal Setting - Help IVD/voip/misc> nat ? - Display the setting IVD/voip/misc> nat -s - Disable NAT traversal function IVD/voip/misc> nat <Disable Mode> - Enable Manual mode and WAN IP Address for NAT router IVD/voip/misc> nat <Manual Mode> <NatIpAddr> - Enable Auto mode and related parameters IVD/voip/misc>...
application-layer protocol that can determine the public IP and nature of a NAT device that sits between the STUN client and STUN server. How to Show VoIP Connection Status - Help IVD/voip> PortStatus ? - Show voip status of port# IVD/voip>...
Class Match Method MatchName MatchIP SpeeddialFrom SpeeddialTo How to Set Allow List of Incoming Calls Setting - Help IVD/voip/sip/incallbarring> allow ? - Display the setting IVD/voip/sip/incallbarring> allow -s - Add the index entry in the allow list IVD/voip/sip/incallbarring> allow –a <Name> <IP/Domain> - Edit the index entry in the allow list IVD/voip/sip/incallbarring>...
How to Set Deny List of Incoming Calls - Help IVD/voip/sip/incallbarring> deny ? - Display the setting IVD/voip/sip/incallbarring> deny -s - Add the index entry in the deny list IVD/voip/sip/incallbarring> deny -a <Name> <IP/Domain> - Edit the index entry in the deny list IVD/voip/sip/incallbarring>...