Press Cutting; Slide (Push) Cutting (Cutting Wide Workpieces); Bevel Cut - Makita LS1219 Instruction Manual

NOTICE:
%HIRUH XVH EH VXUH WR XQORFN WKH VWRS-
per pin and release the handle from the lowered
position.
NOTICE:
'R QRW DSSO\ H[FHVVLYH SUHVVXUH RQ WKH
handle when cutting. Too much force may result in
RYHUORDG RI WKH PRWRU DQGRU GHFUHDVHG FXWWLQJ HI¿-
ciency. Press down handle with only as much force as
QHFHVVDU\ IRU VPRRWK FXWWLQJ DQG ZLWKRXW VLJQL¿FDQW
decrease in blade speed.
NOTICE:
*HQWO\ SUHVV GRZQ WKH KDQGOH WR SHU-
form the cut. If the handle is pressed down with force
or if lateral force is applied, the blade may vibrate and
leave a mark (saw mark) in the workpiece and the
precision of the cut may be impaired.
NOTICE:
'XULQJ D VOLGH FXW JHQWO\ SXVK WKH
carriage toward the guide fence without stopping.
If the carriage movement is stopped during the cut, a
mark will be left in the workpiece and the precision of
the cut will be impaired.

Press cutting

WARNING:
$OZD\V ORFN WKH VOLGLQJ PRYHPHQW
of the carriage when performing a press cutting.
Cutting without lock may cause possible kickback
ZKLFK PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
Workpieces up to 92 mm high and 183 mm wide can be
cut in the following manner.
Fig.43: 1. Stopper pin
1. Push the carriage toward the guide fence until it
stops and lock it with the stopper pin.
2.
Secure the workpiece with the proper type of vise.
3. Switch on the tool without the blade making any
contact and wait until the blade attains full speed before
lowering.
4. Gently lower the handle to the fully lowered posi-
tion to cut the workpiece.
5.
When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
Slide (push) cutting (cutting wide
workpieces)
WARNING:
:KHQHYHU SHUIRUPLQJ D VOLGH FXW
¿UVW SXOO WKH FDUULDJH IXOO WRZDUGV \RX DQG SUHVV
WKH KDQGOH DOO WKH ZD\ GRZQ WKHQ SXVK WKH FDU-
riage toward the guide fence. Never start the cut
ZLWK WKH FDUULDJH QRW SXOOHG IXOO\ WRZDUG \RX If
you perform the slide cut without the carriage pulled
fully toward you unexpected kickback may occur and
VHULRXV SHUVRQDO LQMXU\ PD\ UHVXOW
WARNING:
Never attempt to perform a slide
FXW E\ SXOOLQJ WKH FDUULDJH WRZDUGV \RX Pulling
the carriage towards you while cutting may cause
unexpected kickback resulting in possible serious
SHUVRQDO LQMXU\
WARNING:
Never perform the slide cut with
the handle locked in the lowered position.
Fig.44: 1. Stopper pin
1. Unlock the stopper pin so that the carriage can
slide freely.
2. Secure the workpiece with the proper type of vise.
3. Pull the carriage toward you fully.
4.
Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
5. Press the handle down and push the carriage
toward the guide fence and through the workpiece.
6. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
Miter cutting
5HIHU WR WKH SUHYLRXVO\ FRYHUHG $GMXVWLQJ WKH PLWHU
angle".

Bevel cut

WARNING:
FXW HQVXUH WKDW WKH FDUULDJH DQG EODGH ZLOO KDYH
free travel throughout the entire range of the
intended cut before operating the tool. Interruption
of the carriage or blade travel during the cutting oper-
ation may result in kickback and serious personal
LQMXU\
WARNING:
hands out of the path of the blade. The angle of the
blade may confuse the operator as to the actual blade
path while cutting and contact with the blade will
UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
WARNING:
until it has come to a complete stop. During a
bevel cut the piece cut off may come to rest against
the blade. If the blade is raised while it is rotating the
FXWRII SLHFH PD\EH HMHFWHG E\ WKH EODGH FDXVLQJ
the material to fragment which may result in serious
SHUVRQDO LQMXU\
NOTICE:
:KHQ SUHVVLQJ GRZQ WKH KDQGOH DSSO\
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
Fig.45
1. Remove the upper fence on the side that you are
going to tilt the carriage.
2. Unlock the stopper pin.
3.
$GMXVW WKH EHYHO DQJOH DFFRUGLQJ WR WKH SURFHGXUH
H[SODLQHG LQ WKH $GMXVWLQJ WKH EHYHO DQJOH VHFWLRQ
Then tighten the knob.
4.
Secure the workpiece with a vise.
5.
Pull the carriage toward you fully.
6. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
7. Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade
and push the carriage toward the guide fence to cut
the workpiece.
24 ENGLISH
After setting the blade for a bevel
While making a bevel cut keep
The blade should not be raised