Configure The Its-Dx4020-G Communicator; Configure The Control Panel For Cellular Communication; Configure The Its-Dx4020-G - Bosch ICP-EZM2 Easy Series System Reference Manual

Easy Series
2.8

Configure the ITS-DX4020-G Communicator

2.8.1

Configure the Control Panel for Cellular Communication

You must enabled GSM dialing, and set the format used and the destination IP address and
port number or phone number. You can also configure anti-replay and other parameters. To
do so:
1.
2.
Route 1 Primary (GPRS)
Item Number to Configure
Route 1 Backup (GSM)
Item Number to Configure
Table 2.7 Example Configuration for Cellular Communications
2.8.2

Configure the ITS-DX4020-G

Ensure that the configuration jumper is installed on the CONFIG MODE (J200) pins.
Refer to Section 2.2.5 Install the ITS-DX4020-G Communicator and Antenna, page 15 for proper
installation.
1.
Strength/Comments
Unacceptable—No reading available (modem is resetting or
.
registering)
Attempting to register on the GSM network.
Unacceptable: < -89 dBm.
Acceptable: -89 dBm to -83 dBm.
Good: -83 dBm to -77 dBm.
Very good: -77 dBm to -69 dBm.
Excellent: > -69 dBm.
→
Key: = Scrolling LEDs, from left to right.
Shifting flash = Every other LED flashes simultaneously, creating the shifting flash pattern.
Table 2.8 ITS-DX4020-G Signal Strength LEDs
2.
3.
4.
5.
Bosch Security Systems, Inc.
Enable GSM dialing using Expert Programming Item 202.
For the primary and backup destinations, configure the control panel options as desired.
Refer to Table 2.7, Page 25 for an example of a typical configuration and the
corresponding Expert Programming Items.
Format IP Address/Phone Number
Network 192.168.121.195
211 206
Contact ID 1.585.223.4060
212 207
Observe the LEDs to check for signal strength. Refer to Table 2.8, Page 25. Refer to
Figure 9.1, Page 62 for LED locations.
⊗
= LED's status does not matter.
Call the central monitoring station (CMS) and provide the account number (may be
known as NNC number at the CMS), and control panel polling rate.
Observe the BUS LED. The LED stays on steady when the communicator has permission
to be configured. Refer to Figure 9.1, Page 62 for LED locations. Refer to row 2 in
Table 2.9, Page 26.
Observe the SS1 LED to confirm the ITS-DX4020-G is registered and has sufficient signal
strength to configure it by SMS. The SS1 LED must be On to continue. Refer to
Figure 9.1, Page 62 for LED locations. Refer to Table 2.8, Page 25 for the LED states.
Use the SMS configuration template to send the SMS to the installed SIM card phone
number. For detailed SMS configuration information, refer to Section 9.2 Short Message
Service (SMS) Configuration, page 63.
System Reference Guide
System Installation and Configuration | en
LED State
STATUS CELL IP AUDIO
⊗ ⊗ ⊗
⊗ ⊗ ⊗
⊗ ⊗ ⊗
⊗ ⊗ ⊗
⊗ ⊗ ⊗
⊗ ⊗ ⊗
⊗ ⊗ ⊗
Port Anti-replay
7700 1
241 289
N/A N/A
SS1 SS2 SS3
Off Off Off
Flash Off Off
On Off Off
On Flash Off
On On Off
On On Flash
On On On
F01U087835 | 02 | 2008.10
25
BUS
⊗
⊗
⊗
⊗
⊗
⊗
⊗