Mitsubishi Electric 800 Series Instruction Manual page 380

2.
Tracing
Sampling starts according to the Pr.1020 and Pr.1024 settings.
The trace status can be monitored. (Refer to
3.
Waveform check
By using FR Configurator2, trace data stored in the internal RAM can be displayed on a computer screen. For
details, refer to the Instruction Manual of FR Configurator2.
 Selection of sampling time (Pr.1022, Pr.1023)
• The sampling time is determined by the sampling cycle and the number of data acquisition points. The the number of data
acquisition points varies depending on the setting in Pr.1023 Number of analog channels.
Pr.1023
Number of analog channels
1
2
3
4
5
6
7
8
 Analog source (monitor item) selection
• Select the analog sources (monitor items) to be set to Pr.1027 to Pr.1034 from the following table.
Setting
Monitor item
value
1 Output frequency/speed
2 Output current
3 Output voltage
Frequency setting value/motor
5
speed setting
6 Running speed
7 Motor torque
8 Converter output voltage
9 Regenerative brake duty
Electronic thermal O/L relay load
10
factor
11 Output current peak value
Converter output voltage peak
12
value
13 Input power
14 Output power
17 Load meter
18 Motor excitation current
20 Cumulative energization time
23 Actual operation time
24 Motor load factor
32 Torque command
33 Torque current command
40 PLC function user monitor 1
41 PLC function user monitor 2
page
Memory mode sampling time
Minimum (Pr.1022 = "1")
1704 ms
1280 ms
1024 ms
852 ms
728 ms
640 ms
568 ms
512 ms
Trigger
Minus (-)
*1
level
*2
display
criterion
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
65535
65535
*4
*4
*4
*4
○
*4
○
382.)
Maximum (Pr.1022 = "1000")
1704 s
1280 s
1024 s
852 s
728 s
640 s
568 s
512 s
Setting
Monitor item
value
*3
61 Motor thermal load factor
62 Inverter thermal load factor
67
PID measured value 2
BACnet valid APDU counter (for
83 the FR-E800-EPA and FR-E800-
SCEPA only)
91 PID manipulated amount
97 Dancer main set speed
201 *Output frequency
202 *U-phase output current
203 *V-phase output current
204 *W-phase output current
205 Converter output voltage
206 *Output current (all three phases)
207 *Excitation current (A)
208 *Torque current (A)
209 Terminal 2
210 Terminal 4
212 *Excitation current (%)
213 *Torque current (%)
230 *Output frequency (signed)
231 *Motor speed (with sign)
232 *Speed command (with sign)
235 *Torque command
Number of data
acquisition points
1704
1280
1024
852
728
640
568
512
Trigger
Minus (-)
*1
*2
display
criterion
*4
*4
*4
65535
*4
○
*4
Pr.84
ND rated
○
current
ND rated
○
current
ND rated
○
current
400/800/
1000 V
ND rated
current
ND rated
current
ND rated
current
100%
100%
○ 100%
○ 100%
○ Pr.84
*5
○
*5
○
○ 100%
14.(A) Application Parameters
14.12 Trace function
11
12
13
14
15
16
17
18
level
*3
19
20
379