Mitsubishi Electric 800 Series Instruction Manual page 82

Pr. group Pr.
Extended setting for Ethernet
N648 1457 signal loss detection function
selection
Inverter identification enable/
N649 1399
disable selection [E800-E]
Ethernet communication
N650 1424
network number
Ethernet communication
N651 1425
station number
N660 1442 Ethernet IP filter address 1
N661 1443 Ethernet IP filter address 2
N662 1444 Ethernet IP filter address 3
N663 1445 Ethernet IP filter address 4
Ethernet IP filter address 2
N664 1446
range specification
Ethernet IP filter address 3
N665 1447
range specification
Ethernet IP filter address 4
N666 1448
range specification
Ethernet command source
N670 1449
selection IP address 1
Ethernet command source
N671 1450
selection IP address 2
Ethernet command source
N672 1451
selection IP address 3
Ethernet command source
N673 1452
selection IP address 4
Ethernet command source
N674 1453 selection IP address 3 range
specification
Ethernet command source
N675 1454 selection IP address 4 range
specification
Station number in inverter-to-
N681 1124
inverter link [E800-E]
Number of inverters in
N682 1125 inverter-to-inverter link system
[E800-E]
 (G) Control parameters
Parameters for motor control.
Pr. group Pr.
G000 0 Torque boost
G001 3 Base frequency
G002 19 Base frequency voltage
G003 14 Load pattern selection
G010 46 Second torque boost
G011 47 Second V/F (base frequency)
Energy saving control
G030 60
selection
SF-PR slip amount adjustment
G060 673 operation selection [200 V
class / 400 V class]
*1 For the Ethernet model, the setting is available only when the
FR-A8AY is installed.
*2 For details, refer to the Instruction Manual (Communication).
Refer
Name
to page
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
Refer
Name
to page
Simple Simple Simple 374
Simple Simple Simple 376
376
378
374
376
380
381
Pr. group Pr.
SF-PR slip amount adjustment
G061 674
gain [200 V class / 400 V class]
DC injection brake operation
G100 10
frequency
DC injection brake operation
G101 11
time
G103 850 Brake operation selection
G106 250 Stop selection
Special regenerative brake
G107 70
duty
DC injection brake operation
G110 12
voltage
Regeneration avoidance
G120 882
operation selection
Regeneration avoidance
G121 883
operation level
Regeneration avoidance
G123 885 compensation frequency limit
value
Regeneration avoidance
G124 886
voltage gain
Regeneration avoidance
G125 665
frequency gain
G200 800 Control method selection
G203 245 Rated slip
Slip compensation time
G204 246
constant
Constant output range slip
G205 247
compensation selection
Constant output range torque
G210 803
characteristic selection
G211 820 Speed control P gain 1
G212 821 Speed control integral time 1
Torque control P gain 1
G213 824 (current loop proportional
gain)
Torque control integral time 1
G214 825
(current loop integral time)
Second motor control method
G300 451
selection
G311 830 Speed control P gain 2
G312 831 Speed control integral time 2
Torque control P gain 2
G313 834 (current loop proportional
gain)
Torque control integral time 2
G314 835
(current loop integral time)
G400 286 Droop gain
G401 287 Droop filter time constant
G410 653 Speed smoothing control
Speed smoothing cutoff
G411 654
frequency
Speed control gain (Advanced
G932 89
magnetic flux vector)
Second motor speed control
G942 569
gain
*3 Available when the PLC function is enabled. (Pr.313 to
Pr.315 are always available for settings in the Ethernet
model.)
*4 For the standard model, the setting is available only when a
communication option is installed.
3.3 Parameter list (by function group number)
Refer
Name
to page
381
382
382
382
384
386
382
390
390
390
390
390
86
393
393
393
100,
117
107
107
122
122
86
107
107
122
122
394
394
395
395
90
90
81
3. Parameters
1
2
3
4
5
6
7
8
9
10