Honeywell UDC3500 Product Manual page 11

Table 4-12 Procedure for Using MANUAL TUNE for Heat side of Duplex Control ______________ 199
Table 4-13 Procedure for Using MANUAL TUNE for Cool side of Duplex Control ______________ 199
Table 4-14 Procedure for Accessing Accutune Error Codes _________________________________ 200
Table 4-15 Accutune Error Codes _____________________________________________________ 200
Table 4-16 Set Up Procedure _________________________________________________________ 202
Table 4-17 Procedure for Switching PID SETS from the Keyboard ___________________________ 203
Table 4-18 Logic Gates Constraints and Dynamic Operation Status ___________________________ 206
Table 4-19 Digital Input Option Action on Contact Closure _________________________________ 208
Table 4-20 Digital Input Combinations "DIG IN1" or "DIG IN2" ____________________________ 211
Table 4-21 Digital Inputs 1 and 2 Combination ___________________________________________ 212
Table 4-22 Auto/Manual Station Mode Configuration Procedure _____________________________ 214
Table 4-23 Procedure for selecting Two Loop Algorithm ___________________________________ 220
Table 4-24 Digital Display Indication-Two Loops _______________________________________ 221
Table 4-25 Procedure for Displaying Alarm Setpoints _____________________________________ 223
Table 4-26 Procedure for Displaying TPSC Motor Position _________________________________ 225
Table 4-27 Procedure for Setting a Failsafe Value_________________________________________ 226
Table 4-28 Procedure for Setting a Failsafe Mode_________________________________________ 227
Table 4-29 Running A Setpoint Ramp __________________________________________________ 232
Table 4-30 Program Contents_________________________________________________________ 234
Table 4-31 Run/Monitor Functions ____________________________________________________ 240
Table 5-1 Voltage, Milliamp and Resistance Equivalents for Input Range Values _______________ 258
Table 5-2 Equipment Needed _________________________________________________________ 260
Table 5-3 Set Up Wiring Procedure for Thermocouple Inputs Using an Ice Bath ________________ 262
Table 5-4 Set Up Wiring Procedure for Thermocouple Inputs using a Thermocouple Source _______ 263
Table 5-5 Set Up Wiring Procedure for RTD Inputs _______________________________________ 264
Table 5-6 Set Up Wiring Procedure for Radiamatic, Millivolts, Volts, Carbon, Oxygen or Thermocouple
Differential Inputs (Except 0-10 Volts and -1 to 1 Volts) ________________________________ 265
Table 5-7 Procedure to determine calibration voltages for Thermocouple Differential input types other than the
Factory Setting _________________________________________________________________ 266
Table 5-8 Set Up Wiring Procedure for 0 to 10 Volts or -1 to 1 Volts _________________________ 267
Table 5-9 Set Up Wiring Procedure for Milliampere Inputs _________________________________ 268
Table 5-10 Set Up Wiring Procedure for Dual High Level Voltage Inputs ______________________ 269
Table 5-11 Set Up Wiring Procedure for Dual High Level Milliampere Inputs __________________ 270
Table 5-12 Input Calibration Procedure _________________________________________________ 271
Table 5-13 Restore Factory Calibration _________________________________________________ 273
Table 6-1 Set Up Wiring Procedure for the First Current Output _____________________________ 276
Table 6-2 First Current Output Calibration Procedure______________________________________ 277
Table 6-3 Set Up Wiring Procedure for the Second Current Output ___________________________ 278
Table 6-4 Second Current Output Calibration Procedure ___________________________________ 279
Table 6-5 Set Up Wiring Procedure for the Third Current Output ____________________________ 280
Table 6-6 Third Current Output Calibration Procedure _____________________________________ 281
Table 6-7 Position Proportional and Three Position Step Output Calibration Procedure ___________ 283
Table 6-8 Restore Factory Calibration __________________________________________________ 285
Table 7-1 Procedure for Identifying the Software Version __________________________________ 289
Table 7-2 Procedure for Displaying the Status Test Results _________________________________ 290
Table 7-3 Background Tests__________________________________________________________ 291
Table 7-4 Controller Failure Symptoms_________________________________________________ 295
Table 7-5 Troubleshooting Power Failure Symptoms ______________________________________ 297
Table 7-6 Troubleshooting Current Output Failure ________________________________________ 297
Table 7-7 Troubleshooting Position Proportional Output Failure _____________________________ 299
xi UDC3500 Universal Digital Controller Product Manual 10/05