Electronic Function; Installing Hook - Makita DF001G Instruction Manual

Low speed
Torque level 1
Machine screw M4
Wood Soft wood ø3.5
screw (e.g. pine) x 22
Hard wood –
(e.g. lauan)
Torque level 22
Machine screw
Wood Soft wood
screw (e.g. pine)
Hard wood
(e.g. lauan)
High speed
Torque level 1
Machine screw M4
Wood Soft wood ø3.5
screw (e.g. pine) x 22
Hard wood –
(e.g. lauan)

Electronic function

The tool is equipped with the electronic functions for
easy operation.
• Active Feedback sensing Technology
If the tool is swung at the predetermined accelera-
tion during operation, the motor is forcibly stopped
to reduce the burden on the wrist.
NOTICE:
Hold the tool firmly while operating.
NOTICE:
If any malfunction occurred with the
electronic function, the light blinks for 3 seconds,
and then, turns off. In that case, contact with Makita
Authorized or Factory Service Centers to repair.
NOTE: This function does not work if the acceleration
does not reach the predetermined one when the tool
is swung.
NOTE: If the tool is forcibly stopped, release the
switch trigger, and then pull the switch trigger to
restart the tool.
2 3 4 5 6 7
M5 M6
ø4.1 x 38 –
ø3.5 ø4.1 x 38 –
x 22
23 24 25 26 27
–
–
2 3 4 5 6 7
M5 M6
ø4.1 x 38 –
ø3.5 ø4.1 x 38 –
x 22
8 9 10 11 12
ø5.1 x 50 –
ø5.1 x 50
28 29 30 31 32
–
ø9 x 75 –
ø9 x 75
8 9 10 11 12
ø5.1 x 50 –
ø5.1 x 50
ASSEMBLY
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing side grip (auxiliary handle)
► Fig.9: 1. Side grip 2. Protrusion 3. Groove 4. Arm
Always use the side grip to ensure operating safety.
Install the side grip so that the protrusions on the arm fit
in the grooves on the tool barrel. Turn the grip clockwise
to secure it. The grip can be fixed at desired angle.
Installing or removing driver bit/
drill bit
► Fig.10: 1. Sleeve 2. Close 3. Open
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.

Installing hook

CAUTION:
secure it with the screw firmly. If not, the hook
may come off from the tool and result in the personal
injury.
► Fig.11: 1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
10 ENGLISH
13 14 15 16 17
–
ø6.2 x 63
– ø6.2 x 63
33 34 35 36 37
ø10 x 90
–
13 14 15 16 17
–
ø6.2 x 63
– ø6.2 x 63
Always be sure that the tool is
When installing the hook, always
18 19 20 21
–
–
38 39 40 41
–
ø10 x 90 –
18 19 20 21
–
–