Makita HR262D Technical Information
26mm (1") cordless combination hammers
Hide thumbs
Also See for HR262D:
- User manual ,
- Instruction manual (77 pages) ,
- Instruction manual (77 pages)
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
T
ECHNICAL INFORMATION
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
These 36V cordless combination hammers have been developed based on
Models BHR261 and BHR261T, and feature compatibility with both
Makita 36V-2.6Ah Li-ion battery BL3626 and 36V-2.2Ah Li-ion battery
BL3622A.
(Note: BHR261 and BHR261T run on only 36V-2.6Ah battery BL3626.)
Other features are exactly the same as BHR261 and BHR261T as follows:
• 3 operation modes (rotation only/ rotation with hammering/ hammering only)
• Vibration absorbing handle and soft grips
• Good tool-balance due to the center of gravity closer to handle
HR262TD/BHR262T are equipped with quick change chuck.
These new products are available in the variations listed in the next page.
S
pecification
Voltage: V
Capacity: Ah
Battery
Cell
Energy capacity: Wh
Charging Time: min.
No load speed: min.
¹ = rpm
ˉ
Impacts per minute= min.
Max. output (W)
Chuck type
Capacity: mm (")
Operation mode
Variable speed control
Reverse switch
Torque limiter
LED job light
Weight according to
EPTA-Procedure 01/2003*
*2 Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless).
*3 with Battery and Side grip
S
tandard equipment
Grip assembly ........................ 1
Depth gauge (Stopper pole) ... 1
Quick change drill chuck ....... 1
(for HR262TD/BHR262T)
Bit grease ............................... 1
(for some country)
Waste cloth ............................ 1
(for some country)
Note: The standard equipment
for the tool shown above
may vary by country.
HR262D/BHR262, HR262TD/BHR262T
26mm (1") Cordless Combination Hammers
¹
ˉ
Concrete
Steel
Wood
(Rotation only/ Rotation with hammering/ Hammering only)
: kg (lbs)
3
O
ptional accessories
SDS-PLUS bits
Taper shank TCT bits
Taper shank adapter
Cotter
Grip drill
Grip drill holder
Drill chuck assembly
Chuck adapter
Drill chuck S13
Chuck key S13
SDS-Plus hammer chuck set
Scraper assembly
Dust cup 5
HR262D/ BHR262
2.2/ 2.6
Li-ion
80/ 94
60 with DC36WA/ 22 with DC36RA
0 - 1,200
0 - 4,800
Adapted for
SDS-PLUS bits
26 (1)
13 (1/2)
32 (1-1/4)
3 modes
Yes (by trigger)
4.5 (9.9)
Dust cup 9
Dust extractor attachment
Grease vessel 30g
Hose
Joint 25
Bit grease
Plastic carrying case
Depth gauge (Stopper pole)
Blow out bulb
Cold chisels
Keyless drill chuck
Safety goggles
Dust cup
for ASC & Sales Shop
L
W
Dimensions: mm (")
HR262D/
BHR262
Length (L)
363 (14-1/4)
Width (W)
104 (4-1/8)
Height (H)
235 (9-1/4)
HR262TD/ BHR262T
36
500
Adapted for SDS-PLUS bits
and Round shank bits*
Yes
Yes
Yes
4.8 (10.6)
Grooving chisels
Bull points
Scaling chisels
Fast charger DC36RA
Battery BL3626
Charger DC36WA
Battery BL3622A
Battery adapter BAP36N
Battery converter BCV01
Battery converter BCV02
Side grip set
Grip base set
OFFICIAL USE
PRODUCT
P 1/22
H
HR262TD/
BHR262T
387 (15-1/4)
2
Advertisement
Related Manuals for Makita HR262D
Summary of Contents for Makita HR262D
- Page 1 ONCEPT AND MAIN APPLICATIONS These 36V cordless combination hammers have been developed based on Models BHR261 and BHR261T, and feature compatibility with both Makita 36V-2.6Ah Li-ion battery BL3626 and 36V-2.2Ah Li-ion battery BL3622A. (Note: BHR261 and BHR261T run on only 36V-2.6Ah battery BL3626.) Dimensions: mm (")
- Page 2 P 2/22 ariation list BHR262/ HR262D Plastic Battery Battery Battery Battery Model No. Charger carrying cover adapter converter Type Quantity case BHR262Z BHR262ZC BCV01 BHR262Z2C BCV02 BHR262RD DC36RA BL3626 BHR262RDE DC36RA BL3626 BHR262DP1 DC36RA BL3626 BAP36N HR262DZ HR262DWB DC36WA BL3622A...
-
Page 3: Necessary Repairing Tools
Assembling Ring spring 28 to Tool holder complete/ Tool holder guide complete [2] LUBRICATION Apply the following grease to protect parts and product from unusual abrasion. * Makita grease RB No.00 to the portions indicated by black triangle * Molybdenum disulfide lubricant to the portions indicated by gray triangle Item No. - Page 4 P 4/22 epair [2] LUBRICATION (cont.) Apply Makita grease RB No.00 to the following portions indicated by black triangle to protect parts and product from unusual abrasion. Item No. Description Portion to lubricate BHR262 BHR262T HR262D HR262T Cap 35 Lip portion where Bit is to be inserted...
- Page 5 P 5/22 epair [3] DISASSEMBLY/ASSEMBLY [3] -1. Bit holder section for BHR262, HR262D Holder section for Drill chuck of BHR262T, HR262TD DISASSEMBLING for BHR262, HR262D Fig. 4 Remove Cap 35 with slotted screw- Separate Chuck cover. Bit holder section can be driver, then remove Ring spring 19 Then remove Steel ball 7.0...
- Page 6 (1) Assemble Change ring to Change cover. (Fig. 6) (2) Assemble Torsion spring 31 to Tool holder, then mount Steel balls 6 to Tool holder. (Fig. 7) Note: Apply Makita Grease RB No.00 to Steel balls 6 to prevent them from falling off. Fig. 6 Fig.
- Page 7 P 7/22 epair [3] DISASSEMBLY/ ASSEMBLY [3] -2. Drill chuck assembly for BHR262T, HR262TD DISASSEMBLING Drill chuck assembly can be disassembled as drawn in Figs. 10 to 14. Fig. 10 Fig. 11 After Removing Ring spring 21, strike Drill chuck assembly against Pull off Change cover.
- Page 8 Spacer, mount Drill chuck to Spacer. Chuck holder Spacer Spacer Note: Apply Makita grease RB No.00 to Steel balls 6 to protect them from falling off. Fig. 17 Insert the long arm of Torsion spring 31 By turning Drill chuck...
- Page 9 P 9/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-3. Change lever DISASSEMBLING Fig. 19 While pushing Lock button into Change lever, Insert slotted screwdriver between Change lever and turn Change lever a little over Drill mode position Gear housing complete, then lever up Change lever. to lock it in place.
- Page 10 P 10/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-4. Motor section, Switch DISASSEMBLING Note: Motor section and Switch can be replaced without removing Carbon brushes. Fig. 22 Remove four 4x35 Tapping screws from Gear housing complete and nine 4x18 Tapping screws from Housing (R). Housing (R) can now be removed. Housing (L) Handle (R) Housing (R)
- Page 11 P 11/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-4. Motor section, Switch (cont.) DISASSEMBLING Fig. 26 Remove Brush holder on the right side 4x18 Tapping by unscrewing two 4x18 Tapping screws. screw (2 pcs.) Motor section and Gear section can now Gear section be removed as an assembly.
- Page 12 P 12/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-4. Motor section, Switch (cont.) ASSEMBLING Fig. 29 When inserting Armature into Inner housing complete, do not fail to pass Armature through Yoke unit in advance. M4x12 Hex socket Note: Yoke unit is not directional when assembled head bolt (2 pcs.) with Armature.
- Page 13 P 13/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-5. Tool holder section for BHR262, HR262D/ Tool holder guide section for BHR262T, HR262DT DISASSEMBLING Note: Tool holder (guide) section can be removed without disassembling Housing section. (1) Remove Chuck section as drawn in Figs. 4 and 5.
- Page 14 P 14/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-6. Needle bearing complete and Oil seal 25 DISASSEMBLING Fig. 34 Put Gear housing complete on arbor press table, and keep it upright. Then, by pressing down Oil seal 25 using 1R252, Oil seal 25 and 1R252 Needle bearing complete can be removed from Gear housing complete Gear housing...
- Page 15 P 15/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-7. Impact bolt in Tool holder complete for BHR262, HR262D)/ Tool holder guide complete for BHR262T, HR262TD DISASSEMBLING (1) When Striker is left in Tool holder (guide) complete, push Striker out of Tool holder (guide) complete by inserting 1R281 from the top end then by striking 1R281 with plastic hammer.
- Page 16 P 16/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-7. Impact bolt in Tool holder complete for BHR262, HR262D)/ Tool holder guide complete for BHR262T, HR262TD (cont.) ASSEMBLING 1) Assemble Impact bolt section to Tool holder (guide) complete as drawn in Fig. 42. Fig. 42 Note: The five components are directional, and must be mounted as shown below.
- Page 17 P 17/22 epair [3] DISASSEMBLY/ASSEMBLY [3]-8. Swash bearing 10, Gear section DISASSEMBLING Fig. 44 Note: This step can be done without removing Motor section. 1) Remove Gear housing complete as instructed in [3]-5. Inner housing complete 2) Remove Inner support complete by loosening two M4x25 Hex socket head bolts using 1R170.
- Page 18 ASSEMBLING Fig. 51 Note: Be sure to apply Makita grease RB No.00 and Molybdenum disulfide lubricant to the specific portions shown in Figs. 1, 2 and 3. 1) Onto Cam shaft, slide Swash bearing 10, Sleeve 9, Spiral bevel gear 26 Guide plate in order, then press-fit them using 1R032, 1R033 and arbor press.
-
Page 19: Maintenance Program
It is recommended to replace the following parts at the same time when replacing Carbon brushes. (Fig. 55) Note: Be sure to put Makita grease RB No. 00 and Molybdenum disulfide lubricant to the specific portions. Refer to Figs. 1, 2 and 3. -
Page 20: Ircuit Diagram
P 20/22 ircuit diagram Fig. D-1 Color index of lead wires' sheath Black White Yellow Without Equipment of Radio Interference Suppression Switch Brush holder T – Terminal With Equipment of Radio Interference Suppression Brush holder complete Line filters M1 M2 Switch T –... -
Page 21: Wiring Diagram
P 21/22 iring diagram Fig. D-2 [Wiring in Handle Section] Lead wires must be tight in the area shown in gray. Fix lead wires in the Lead wire holders indicated by dotted circle. Lead wire holders Switch Diode ribs inner wall of Housing To Brush holder complete... - Page 22 P 22/22 iring diagram Fig. D-3 [Wiring in Motor Section] Fix Lead wires (red, black) of Brush holder complete in these Lead wire holders. Connector Lead wire (black) Tube Lead wire holder Yoke Terminal Line filters Light circuit Line filter is not used Lead wire (yellow) for some countries.