Makita HR2610 Technical Information
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Power Tool
  5. HR2610
  6. Technical information

Makita HR2610 Technical Information

Combination hammers 26mm (1")
Hide thumbs Also See for HR2610:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
T
ECHNICAL INFORMATION
Model No.
Description
C
ONCEPT AND MAIN APPLICATIONS
HR2610 series models are 26mm (1") combination hammers adapted for
SDS-PLUS bits, featuring compact and lightweight design, enhanced comfort
and better control with ergonomic handle. Model HR2610T/HR2611FT are
equipped with quick change drill chuck while Model HR2611/HR2611FT are
with AVT; Anti Vibration Technology consisting of Active dynamic vibration
absorber with counterweight and Damper spring. AVT ensures operation with
extremely low vibration, which is much superior to the competitors.
HR2610 series models are available in the variations listed below, including
HR2300 and HR2600 series models developed on the same concept.
Model
Capacity
HR2300
23mm
HR2600
HR2601
26mm
HR2610
HR2611F
HR2310T
23mm
HR2610T
26mm
HR2611FT
For information of HR2300 and HR2600 series models,
see "
TECHNICAL INFORMATION
S
pecification
Voltage (V)
110
120
127
220
230
240
Specification
No load speed: minֿ¹= rpm
Impacts per minute= minֿ¹
Chuck type
TCT bit
Core bit
Capacities:
Diamond core bit
mm (")
Steel
Wood
Operation mode
Vibration absorption
Variable speed control
Rotation reversing facility
Torque limiter
LED Job light
Double insulation
Power supply cord: m (ft)
Weight according to
EPTA-Procedure 01/2003
*1 Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless).
*2 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring
*3 with side grip
HR2610/ HR2611F/ HR2610T/ HR2611FT
Combination Hammers 26mm (1")
Operation Mode
AVT
No
2 modes
(Rotation only/
No
Rotation with hammering)
Yes
No
3 modes
Yes
(Rotation only/
No
Rotation with hammering/
No
Hammering only)
Yes
" of each series.
Current (A)
Cycle (Hz)
7.7
50/ 60
7
50/ 60
6.6
50/ 60
3.8
50/ 60
3.7
50/ 60
3.5
50/ 60
Model
: kg (lbs)
*3
LED
Chuck type
No
No
Adapted for
No
SDS-PLUS shank bits
No
Yes
No
Adapted for
No
SDS-PLUS shank bits
and Round shank bits*
Yes
Continuous Rating (W)
Input
800
---
800
800
800
800
HR2610/ HR2611F
Adapted for
SDS-PLUS shank bits
68 (2-11/16)
80 (3-1/8)
32 (1-1/4)
(Rotation only/ Rotation with hammering/ Hammering only)
No/ Yes (AVT
)
*2
Yes (by trigger)
No/ Yes
Europe, North America: 4.0 (13.1), Australia, Brazil: 2.0 (6.6),
Other countries: 2.5 (8.2)
2.8/ 2.9
(6.1/ 6.4)
L
W
(The image above is
HR2610/HR2611F.)
Dimensions: mm (")
HR2610
HR2611F HR2611FT
Length (L)
361 (14-1/4) 385 (15-1/8)
Width (W)
Height (H)
209 (8-1/4)
*Round shank bits can also be used by
replacing the factory-mounted chuck with
Quick change drill chuck (keyless).
Max. Output (W)
Output
400
400
400
400
400
400
HR2610T/ HR2611FT
0 - 1,200
0 - 4,600
Adapted for SDS-PLUS shank bits
and Round shank bits
26 (1)
13 (1/2)
3 modes
No/ Yes (AVT
Yes
Yes
No/ Yes
Yes
2.9/ 3.0
(6.4/ 6.6)
PRODUCT
P 1/ 22
H
HR2610T
77 (3)
550
550
550
550
550
550
*1
)
*2

Advertisement

Table of Contents
loading

Related Manuals for Makita HR2610

Summary of Contents for Makita HR2610

  • Page 1 Damper spring. AVT ensures operation with extremely low vibration, which is much superior to the competitors. (The image above is HR2610 series models are available in the variations listed below, including HR2610/HR2611F.) HR2300 and HR2600 series models developed on the same concept.

  • Page 2: Standard Equipment

    P 2/ 22 tandard equipment Depth gauge ..........1 Side grip ........... 1 Dust cup set ..........1 (for some countries only) Quick change drill chuck (keyless) ... 1 (HR2610T/ HR2611FT only) Carrying case ..........1 (plastic or aluminum) Note: The standard equipment for the tool shown above may vary by country. ptional accessories SDS-PLUS shank TCT hammer drill bits Dust cups 5 and 9...

  • Page 3: Necessary Repairing Tools

    CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”. [1] NECESSARY REPAIRING TOOLS Code No. Description Use for removing Ring spring 14 and 15 from Tool holder complete for HR2610/ HR2611F 1R003 Retaining ring S pliers ST-2N removing Ring spring 19 from Tool holder for HR2610T/ HR22611FT 1R004...

  • Page 4: Lubrication (Hr2610/11F)

    P 4/ 22 epair [2] LUBRICATION (for HR2610/ HR2611F) Apply the following grease/ lubricant to protect parts and product from unusual abrasion. Item No. Description Portion to lubricate Grease/ Lubricant Amount Cap 35 Lip portion where Bit is to be inserted...

  • Page 5: Lubrication (Hr2610T/11Ft)

    10 HR2611FT Clutch cam A (h ) Quick change drill chuck Apply Makita grease RB No. 00 to the entire surface of two Steel ball 6 and one Steel ball 5. 70 71 Steel ball 5 Steel ball 6 (2 pcs.)

  • Page 6: Bit Holder Section (Hr2610/11F)

    P 6/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-1A. Bit holder section for HR2610/ HR2611F DISASSEMBLING Fig. 3 (1) Remove Cap 35. Cap 35 1R003 (2) Separate Ring spring 14 from the groove of Tool holder complete using 1R212 1R003 with 1R212. (Fig. 3) Washer 16 on Ring spring 15 is removed.

  • Page 7: Holder Section For Drill Chuck (Hr2610T/11Ft)

    P 7/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-1B. Holder section for Drill chuck for HR2610T/ HR2611FT DISASSEMBLING (1) Remove Tool holder set from Tool holder guide complete. (Fig. 7) (2) Remove Cap 35, then separate Ring spring 19 from the groove of Tool holder using 1R003 with 1R212. (Fig. 8) (3) Remove Chuck cover, then remove Steel ball 7.0 while pressing down Stopper.
  • Page 8 Tool holder • Insert the short arm of Torsion spring 31 into the hole of Tool holder. Note: Apply Makita grease No. RB No. 00 to two Steel balls 6 to prevent them from falling. (Fig. 13) (2) Assemble Change ring to Change cover. (Fig. 14) long arm (3) Assemble Tool holder to Change cover.

  • Page 9: Drill Chuck Assembly (Hr2610T/11Ft)

    P 9/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-2. Drill chuck assembly for HR2610T/ HR2611FT DISASSEMBLING Drill chuck assembly can be disassembled as drawn in Figs. 17 to 21. Fig. 17 Fig. 18 After Removing Ring spring 21, strike Drill chuck assembly against Pull off Change cover.
  • Page 10 Spacer, mount Drill chuck to Spacer. Chuck holder Spacer Spacer Note: Apply Makita grease RB No.00 to Steel balls 6 to protect them from falling off. Fig. 24 Insert the long arm of Torsion spring 31 By turning Drill chuck...
  • Page 11 P 11/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-3. Change lever section Fig. 26 DISASSEMBLING Insert the tip of thin slot screwdriver into the notch of Gear housing Change lever cover A complete, then lever up one side of Change lever cover A. (Fig. 26) Lever up the other side of Change lever cover A in the same way, then remove Change lever cover A.
  • Page 12 [3] DISASSEMBLY/ASSEMBLY [3]-5. Torque limiter section Fig. 31 DISASSEMBING (1) Remove Bit holder section (HR2610, HR2611F) / Holder section (HR2610T, HR2611FT). (2) Remove Change lever section. Tool holder (3) Separate Gear housing complete from Motor housing complete. (guide) (4) Remove Tool holder complete (HR2610, HR2611F) / Tool holder guide complete complete (HR2610T, HR2611FT) by tapping the top as drawn in Fig.

  • Page 13: Impact Bolt/Tool Holder (Hr2610/T & 11F/T)

    Vise. (Fig. 38) O-ring case A (HR2610, HR2610T) / O-ring case B (HR2611F, HR2611FT) is moved toward the top of Tool holder (guide) complete, and therefore, Ring spring 28 can be relieved from O-ring case A/ B.
  • Page 14 P 14/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-6. Impact bolt section in Tool holder complete for HR2610/ HR2610F Tool holder guide complete for HR2610T/ HR2611FT (cont.) ASSEMBLING (1) Assemble Impact bolt section to Tool holder (guide) complete as drawn in Fig. 40A/ 40B.
  • Page 15 [3] DISASSEMBLY/ASSEMBLY [3]-6. Impact bolt section in Tool holder complete for HR2610/ HR2610F Tool holder guide complete for HR2610T/ HR2611FT (cont.) (2) Push Ring spring 28 into the inner groove of Tool holder (guide) complete as drawn in Fig. 41.
  • Page 16 P 16/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-7. Swash bearing section DISASSEMBLING (1) Disassemble Motor housing section, Gear housing section and Inner housing section. As for HR2610F and HR2611F, remove two M4x12 Hex socket head bolts. And then separate Counter weight section from Inner housing complete. (Fig.
  • Page 17 P 17/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-7. Swash bearing section (cont.) ASSEMBLING (1) Pressfit Ball bearing 608ZZ into Bearing box. (2) Put Swash bearing 10, Flat washer 8 and Bearing box to Cam shaft in order, then secure them using 1R032, 1R026 and arbor press.
  • Page 18 P 18/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-9. How to assemble Gear housing to Inner housing Fig. 50 (1) Check that Clutch cam A is engaged with Swash bearing 10. (Fig. 50) Swash bearing 10 (2) Assemble Compression spring 4 and Lock plate to Gear housing complete.

  • Page 19: Oil Seal 25/Cup Sleeve/Ball Bearing

    P 19/ 22 epair [3] DISASSEMBLY/ASSEMBLY [3]-10. Oil seal 25, Cup sleeve, Ball bearing 6806LLU DISASSEMBLING (1) Assemble Inner housing complete to Gear housing complete. (2) Put Inner housing complete on U-groove table portion of arbor press, then press Oil seal 25, Cup sleeve and Ball bearing 6806LLB out of Gear housing complete using 1R252.

  • Page 20: Maintenance Program

    It is recommended to replace the following parts at the same time when replacing Carbon brushes. (Figs. 58 and 59) Note: Be sure to put Makita grease RB No. 00 to the specific portions. (Figs. 1 and 2) Fig. 58...
  • Page 21 P 21/ 22 epair [4] Maintenance program (cont.) Fig. 59 HR2611F Cap 35 (286288-8) Ring spring 15 (233992-0) Rubber washer 16 Ring spring 14 (424364-2) (233989-9) 26 Steel ball 7 (2 pcs.) (216022-2) O ring 9 (213073-6) 45 O ring 17.5 (213258-4) 43 Ring spring 28 (233979-2)

  • Page 22: Circuit Diagram

    P 22/ 22 ircuit diagram Fig. D-1 Brush holder unit Noise suppressor (if used*) Switch* LED circuit (HR2611F/ FT only) Strain relief Power supply cord * To comply with the electromagnetic compatibility-requirement, Switch equipped with Noise suppressor is used for some countries.

This manual is also suitable for:

Hr2610tHr2611fHr2611ft

Table of Contents