Siemens SINUMERIK Series Function Manual page 15

7.5.3 Types of workpiece measurement.............................................................................................466
7.5.3.1 Measurement of an edge (measurement type 1, 2, 3) ..............................................................466
7.5.3.2 Measurement of an angle (measurement type 4, 5, 6, 7)..........................................................470
7.5.3.3 Measurement of a hole (measurement type 8)..........................................................................473
7.5.3.4 Measurement of a shaft (measurement type 9).........................................................................476
7.5.3.5 Measurement of a groove (measurement type 12)....................................................................477
7.5.3.6 Measurement of a web (measurement type 13) ........................................................................480
7.5.3.7 Measurement of geo axes and special axes (measurement type 14, 15).................................481
7.5.3.8 Measurement of an oblique edge (measurement type 16)........................................................483
7.5.3.9 Measurement of an oblique angle in a plane (measurement type 17) ......................................485
7.5.3.10 Redefine measurement around a WCS reference frame (measurement type 18)....................488
7.5.3.11 Measurement of a 1-, 2- and 3-dimensional setpoint selection (measurement type 19, 20,
21) ..............................................................................................................................................492
7.5.3.12 Measuring a measuring point in any coordinate system (measurement type 24) .....................496
7.5.3.13 Measurement of a rectangle (measurement type 25)................................................................500
7.5.3.14 Measurement for saving data management frames (measurement type 26)............................501
7.5.3.15 Measurement for restoring backed-up data management frames (measurement type 27) ......502
7.5.3.16 Measurement for defining an additive rotation for taper turning (measurement type 28)..........503
7.5.4 Tool measuring ..........................................................................................................................504
7.5.5 Types of workpiece measurement.............................................................................................505
7.5.5.1 Measurement of tool lengths (measurement type 10) ...............................................................505
7.5.5.2 Measurement of tool diameter (measurement type 11).............................................................507
7.5.5.3 Measurement of tool lengths with zoom-in function (measurement type 22) ............................508
7.5.5.4 Measuring a tool length with stored or current position (measurement type 23).......................509
7.5.5.5 Measurement of a tool length of two tools with the following orientation: .................................511
7.6 Measurement accuracy and functional testing ..........................................................................523
7.6.1 Measurement accuracy..............................................................................................................523
7.6.2 Probe function test .....................................................................................................................524
7.7 Simulated measuring .................................................................................................................525
7.7.1 General functionality ..................................................................................................................525
7.7.2 Position-related switch request ..................................................................................................525
7.7.3 External switch request..............................................................................................................527
7.7.4 System variable..........................................................................................................................528
7.8 Channels - only 840D sl.............................................................................................................528
7.8.1 Measuring mode 1 .....................................................................................................................528
7.8.2 Measuring mode 2 .....................................................................................................................529
7.8.3 Continuous measurement..........................................................................................................529
7.8.4 Functional test and repeat accuracy..........................................................................................531
7.9 Data lists ....................................................................................................................................532
7.9.1 Machine data..............................................................................................................................532
7.9.1.1 General machine data................................................................................................................532
7.9.1.2 Channel-specific machine data..................................................................................................533
7.9.2 System variables........................................................................................................................533
8 N3: Software cams, position switching cycles - only 840D sl ................................................................. 535
8.1 Brief Description.........................................................................................................................535
8.2 Cam signals and cam positions .................................................................................................536
8.2.1 Generation of cam signals for separate output..........................................................................536
8.2.2 Generation of cam signals with gated output.............................................................................539
Extended Functions
Function Manual, 03/2013, 6FC5397-1BP40-3BA1
Contents
15