Samsung DCS Programming Manual page 395

SAMSUNG
COMBINED SYSTEMS PROGRAMMING MANUAL
ALM CODE ALARM
MJB06 IPC MSGQ Over
MJB06 IPC MSGQ Under
MJB07 Task MSGQ Over
Task MSGQ Un-
MJB07
der
MJC01 DTMF Fault
MJC02 Tone Fault
MJC10 AA-DTMF Fault
MJC11 AA-MFR Rec
MJC12 E911 Restart
MJC13 E911 Block
MJC14 VoIP Restart
MJC15 VoIP Block
MJD01 Sync Failure
MJD02 Sync Recovery
MJD03 Red Alarm
MJD04 Red Alarm Rec
MJD05 Yellow Alarm
MJD06 Yellow Alarm Rec
MJD07 Blue Alarm
MJD08 Blue Alarm Rec
IPC TX queue full error has occurred in the MCP.
Alarm data = IPC Queue type
(MCP-LAN, MCP-SCP, MCP-LCP1, MCP-LCP2)
IPC TX queue under error has occurred in the MCP.
Alarm data = IPC Queue type
(MCP-LAN, MCP-SCP, MCP-LCP1, MCP-LCP2)
Task MSG queue full error has occurred in the MCP.
Alarm data = Error Task Kind
(CNFG, ERRH, NPER, MSGH, DIGH, SMART, CALL, PPER,
SMDR, TMMC, IDLE)
Task MSG queue under error has occurred in the MCP.
Alarm data = Error Task Kind
(CNFG, ERRH, NPER, MSGH, DIGH, SMART, CALL, PPER,
SMDR, TMMC, IDLE)
An abnormal interrupt has occurred in the system DTMF
resources.
Alarm data = DTMF Receiver number (BASE, MISC)
An abnormal interrupt has occurred in the system tone resources,
i.e. busy, ringback, error, no more calls etc.
Alarm data = TONE Receiver number (BASE, MISC)
An abnormal fault reported in one of the systems AA card DTMF
resources.
Alarm data = Cabinet, Slot, Port (Cx–Syy-Pzz)
An abnormal fault reported in one of the systems AA card DTMF
resources has recovered.
Alarm data = Cabinet, Slot, Port (Cx–Syy-Pzz)
The E911 card has restarted.
Alarm data = Cabinet, Slot (Cx–Syy)
The E911 card has restarted because the system detected the
card does not work correctly.
Alarm data = Cabinet, Slot (Cx–Syy)
The ITM3/MGI card has restarted.
Alarm data = Cabinet, Slot (Cx–Syy)
The ITM3/MGI card has restarted because the system detected
the card does not work correctly.
Alarm data = Cabinet, Slot (Cx–Syy)
Clocking on TEPRI cards has become asynchronous.
Clocking on TEPRI cards has become synchronous.
Locally detected loss of PCM carrier on TEPRI card for more
than 250 ms.
Alarm Data = Cabinet, Slot (Cx-Syy)
PCM carrier detected locally on TEPRI cards.
Alarm Data = Cabinet, Slot (Cx-Syy)
Remotely detected failure transmitted in frame on TEPRI card.
Alarm Data = Cabinet, Slot (Cx-Syy)
Remotely detected failure restored transmitted on TEPRI card.
Alarm Data = Cabinet, Slot (Cx-Syy)
All 1's being transmitted on facility on TEPRI card.
Alarm Data = Cabinet, Slot (Cx-Syy)
A blue alarm condition has been cleared.
Alarm Data = Cabinet, Slot (Cx-Syy)
MMC 851 (Page 3 of 5)
MMC PROGRAMS
FEBRUARY 2004
DEFINITION