Area Properties - Bosch Solution 64 Installer's Manual

Solution 64 | Installer Guide | Area Programming
Areas > Commands >
Turn All Areas On
This command allows you to turn on all areas that your PIN
has been assigned to at the same time. An alternative method
for arming all areas is to enter your PIN then press an hold the
[ON] key for 2 seconds.
1) Enter [MENU] + [2] + [0] + [2]. The keypad will display the exit
time bar to prompt you to exit all areas. You should leave all
areas now.
2) When exit time has expired, the keypad will display that all
areas are turned All On (Armed).
Area 1 Name
EXIT NOW
i
The Display Area Icons option is programmable per keypad. If
this option has not been selected then Area icons 1 to 8 will not
be displayed. See Menu 6-1-4 — Display Area Icons.
Note
Areas > Commands >
Turn All Areas Off
This command allows you to turn off all areas that your PIN has
been assigned to at the same time. This command cannot be
accessed from a keypad that is in the armed state.
Enter [MENU] + [2] + [0] + [3] to disarm all areas.
1)
An alternative method for disarming all areas is to enter your
2)
PIN then press an hold the [OFF] key for 2 seconds.
Areas > Commands >
Move To Area
Each keypad on the system can opererate any area however
you can only operate the area which is currently being
displayed. The Move to Area command allows you to change
the current keypad view from one area to another.
An alternative method for changing the current area being
displayed is to enter your PIN and then press the left or right
arrow keys. Keep pressing the arrow key until the desired area
is displayed. Only areas which have been assigned to the PIN
will be available for view.
If you move to another area the keypad will automatically
revert back to its assigned home area after 2 minutes. See
Menu 6-1-3, Home Area.
1) Enter [MENU] + [2] + [0] + [4] and select the area from the list
and press [OK] to move to the selected area.
6-2
- -
MENU 2-0-2
  
- -
MENU 2-0-3
  
-
MENU 2-0-4
 
A001 Security System
A002 Area 2 Name
A003 Area 3 Name
Press  OK or MENU
i
Turn off option Menu 6-1-4, Pin To change Area and use the [←]
and [→] keys to move through all areas on the system without
the need to enter your pin.
Note
Areas > Commands >
Chime On/Off
Chime mode allows you to monitor a zone (or group of zones)
by sounding the keypad buzzer or activating a programmable
output. This can be useful when you need to monitor the front
or back entrance to a premises while in the disarmed state.
To select which zones will be monitored for chime see Menu 3-
0-3 — Set Chime Zones.
1) To turn chime mode On or Off enter [MENU] + [2] + [0] + [5]
and select the area from the list then press [OK].
Security System A001
Chime is OFF
To turn ON, Press ON
To Go Back Press OK
i
The Chime Tone will only be heard on keypads programmed to
sound the chime tone. See Menu 6-1-5 — Chime Tone
Note
Area Pro pe rtie s
Areas > Area Properties >
Area Name
A r e a 1
This menu allows you to program the name for each area. Each
area name can be programmed with up to 16 characters. At
factory default, only Area 1 is used. The Solution control panel
can have a maximum of 8 independent areas programmed.
Enter [MENU] + [2] + [1] + [0] and select the area from the list
1)
and press [OK].
Area Name A001
Security System
Press  OK to SAVE
2) Use the arrow and number keys to move and change text.
When the Area Name is complete, press [OK]. At any time you
can press the [OFF] key to clear the text from the current cursor
position to the end of the line.
i
See Alpha Text section in Section 4 - Programming Overview for
further detail on entering alpha text.
Note
- - -
MENU 2-0-5
   
-
MENU 2-1-0
 
N a m e
Bosch Security Systems | 11/05 | BLCC110I