User Tokens - Bosch Solution 64 Installer's Manual

i
If you attempt to enter a new PIN which already exists the
system will display PIN Not Allowed. The next time the original
PIN holder disarms the system they will be notified that their PIN
Note
code has been compromised. The compromised PIN message
will continue to be displayed until the original user changes
their PIN.
Access > PIN Codes >
Add PIN
This command allows the Installer or Master user to add a PIN
for a user that currently does not have a PIN assigned.
The Master user can only program a new PIN for users that
have been assigned to the same area(s) as the Master user.
1) Enter [MENU] + [1] + [1] + [2] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that dont already have PINs assigned.
Ur006 User 6 Name
Ur008 User 8 Name
Ur010 User 10 Name
Press  OK or MENU
2) Enter the new PIN, then press [OK]. If the error message "PIN
Not Allowed" is displayed , press [OK] and try a different PIN.
Enter New PIN for
User 10 Name Ur010
••••
Press OK or MENU OK or MENU
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
i
If you attempt to enter a new PIN which already exists the
system will display PIN Not Allowed. The next time the original
PIN holder disarms the system they will be notified that their PIN
Note
code has been compromised. The compromised PIN message
will continue to be displayed until the original user changes
their PIN.
Access > PIN Codes >
Delete PIN
This menu allows security installers and Master Users the
ability to delete other users PINs. A Master user can only delete
a PIN for users that have been assigned to the same area(s). The
Installer and Master user cannot delete their own PIN.
1) Press [MENU] + [1] + [1] + [3] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that can be deleted.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name

Press OK or MENU
2) Press [OK] to delete the PIN or press [MENU] to cancel.
Press OK to delete PIN
User Ur002 Debbie Smith
Press OK or MENU OK or MENU
Bosch Security Systems | 11/05 | BLCC110I
-
MENU 1-1-2
 
-
MENU 1-1-3
 
Solution 64 | Installer Guide | Access Programming
Access > PIN Codes >
View PIN
This menu allows the Installer to view the actual PIN for any
user.
1) Press [MENU] + [1] + [1] + [4] and use the up and down arrows
to highlight the user in the list then press [OK].
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name

Press OK or MENU
2) The PIN will always display 8 digits however only the number
of digits corresponding to the global PIN Length setting are
valid.
View PIN Ur001
25800000
Press 0-9 OK to SAVE OK to SAVE
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
U ser To ken s
This section outlines how to add and delete tokens. Tokens
provide an alternate method for users to turn the system on
and off or operate a door strike.
A token is a plastic card that has a unique ID number. Each
user can be assigned a PIN as well as a Token for greater
flexibility.
A Token can be presented to a keypad with a built in reader or
to an external reader module to operate the system.
Tokens will follow all user settings.
Access > Token >
Add Token
This command allows the Installer or Master User to assign
a Token ID for each user. Only one Token can be assigned to
each user. To change a Token for an existing user you will need
to first delete the old Token before adding the new one.
See MENU 1-2-1 — Delete Token
1) Enter [MENU] + [1] + [2] + [0] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that dont already have Tokens assigned.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name
Press  OK or MENU
Swipe the token card past the reader. As you swipe the token,
2)
the reader will sound a single beep to confirm that the token
has been learnt.
MENU 1-1-4

-
MENU 1-2-0
 
5-3