Samsung SRP-370 User Manual page 42

GS r n
[Name] Transmit status.
[Format] ASCII GS
Hex 1D
Decimal 29
[Range] n=1, 2, 49, 50
[Description] ▪ Transmits the normal status specified by n as follows :
n Function
1, 49 Transmits paper sensor status.
2, 50 Transmits drawer kick-out connector status.
▪ Paper sensor status (n=1, 49) :
Bit Off/On Hex Decimal
Off 00
0, 1
On 03
Off 00
2, 3
On 0C
4 Off 00
5 Off 00
6 Off 00
7 Off 00
- Bits 2 and 3 : This command cannot be executed since the printer
becomes offline when the paper roll end sensor detects the paper not
present. Therefore, the status of bit 2 (1) and bit 3 (1) is not transmitted.
▪ Drawer kick-out connector status (n=2, 50) :
AAWBit Off/On Hex
Off 00
0
On 01
1 Off 00
2 Off 00
3 Off 00
4 Off 00
5 Off 00
6 Off 00
7 Off 00
GS v 0 m xL xH yL yH d1...dk
[Name] Print raster bit image.
[Format] ASCII GS v
Hex 1D 76
Decimal 29 118
[Range] 0 ≤ m ≤ 3, 48 ≤ m ≤ 51
1 ≤ (xL + xH x 256) ≤ 128 (0 ≤ xL ≤ 128, xh=0)
1 ≤ (yL + yH x 256) ≤ 4095 (0 ≤ yL ≤ 255, 0 ≤ yH ≤ 15)
0 ≤ d ≤ 255
k = (xL + xH x 256) x (yL + yH x 256)
r n
72 n
114 n
Function
0 Paper roll near-end sensor : paper adequate.
3 Paper roll near-end sensor : paper near end.
0 Paper roll end sensor : paper present.
12 Paper roll end sensor : paper not present.
0 Fixed.
0 Reserved.
0 Reserved.
0 Fixed.
Decimal Function
0 Drawer kick-out connector pin 3 is LOW.
1 Drawer kick-out connector pin 3 is HIGH.
0 Reserved.
0 Reserved.
0 Reserved.
0 Fixed.
0 Reserved.
0 Reserved.
0 Fixed.
0 m xL xH yL yH d1...dk
30 m xL xH yL yH d1...dk
48 m xL xH yL yH d1...dk
82
[Description] ▪ Prints a raster bit image in m mode.
- m specifies the bit image mode.
<For SRP-370>
m Mode
0, 48 Normal
1, 49 Double-width
2, 50 Double-height
3, 51 Quadruple
<For SRP-372>
m Mode
0, 48 Normal
1, 49 Double-width
2, 50 Double-height
3, 51 Quadruple
- xL, xH specifies (xL + xH x 256) byte(s) in the horizontal direction for the bit image.
- yL, yH specifies (yL + yH x 256) dot(s) in the vertical direction for the bit image.
- d specifies the definition data of the bit image data.
GS w n
[Name] Set bar code width.
[Format] ASCII GS
Hex 1D 77
Decimal 29 119
[Range] 2 ≤ n ≤ 6
n=3
[Description] ▪ Set the horizontal size of the bar code, using n as follows :
<For SRP-370>
Multi-level Bar Code
n
Module Width (mm)
2 0.282
3 0.423
4 0.564
5 0.706
6 0.847
<For SRP-372>
Multi-level Bar Code
n
Module Width (mm)
2 0.250
3 0.375
4 0.500
5 0.626
6 0.751
[Notes]
▪ Multi-level bar codes are as follows :
- UPC-A, UPC-E, JAN13, HAN8, CODE93, CODE128
▪ Binary-level bar codes are as follows :
- CODE39, ITF, CODABAR
Vertical dot density Horizontal dot density
180 dpi 180 dpi
180 dpi 90 dpi
90 dpi 180 dpi
90 dpi 90 dpi
Vertical dot density Horizontal dot density
203 dpi 203 dpi
203 dpi 203/2 dpi
203/2 dpi 203 dpi
203/2 dpi 203/2 dpi
dpi : dots per 25.4mm {1"}
w n
n
n
Binary-level Bar Code
Thin element width (mm) Thick element width (mm)
0.282 0.706
0.423 1.129
0.564 1.411
0.706 1.834
0.847 2.258
Binary-level Bar Code
Thin element width (mm) Thick element width (mm)
0.250 0.626
0.375 1.001
0.500 1.251
0.626 1.627
0.751 2.002
83