Samsung SRP-370 User Manual page 27

▪ For SRP-372 :
- When a paper width of 80mm{3.15"} is selected :
(xL + xH x 256) = 0 (xL=0, xH=0)
(yL + yH x 256) = 0 (yL=0, yH=0)
(dxL + dxH x 256) = 576 (dxL=64, dxH=2)
(dyL + dyH x 256) = 1476 (dyL=196, dyH=5)
- When a paper width of 60mm{2.36"} is selected :
(xL + xH x 256) = 0 (xL=0, xH=0)
(yL + yH x 256) = 0 (yL=0, yH=0)
(dxL + dxH x 256) = 380 (dxL=128, dxH=1)
(dyL + dyH x 256) = 1476 (dyL=196, dyH=5)
[Description] ▪ Set the position and the size of the printing area.
- Horizontal starting position = [(xL + xH x 256) x (horizontal motion unites)].
- Vertical starting position = [(yL + yH x 256) x (vertical motion unites)].
- Horizontal printing area width = [(dxL + dxH x 256) x (horizontal motion unites)].
- Vertical printing area width = [(dyL + dyH x 256) x (vertical motion unites)].
▪ The maximum printable area is 117.263mm {1662/360"} maximum.
ESC ＼ nL nH
[Name] Set relative print position.
[Format] ASCII ESC
Hex 1B
Decimal 27
[Range]
0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nL 255, 0 ≤ nH ≤ 255)
[Description]
▪ Set the print starting position based on the current position to [(nL + nH
× 256) × horizontal or vertical motion unit]
- When (nL + nH × 256) is positive number, the print starting position is
specified to the right based on the current position.
- When (nL + nH × 256) is negative number, the print starting position is
specified to the left based on the current position.
ESC a n
[Name] Select justification.
[Format] ASCII ESC
Hex 1B
Decimal 27
[Range] 0 ≤ n ≤2, 48 ≤ n ≤50
[Default] n=0
[Description] ▪ In standard mode, aligns all the data in one line to the position specified by n as follows :
n Justification
0, 48 Left justification
1, 49 Centering
2, 50 Right justification
nL nH
＼
5C nL nH
92 nL nH
a n
61 n
97 n
52
ESC c 3 n
[Name] Select paper sensor(s) to output paper end signals.
[Format] ASCII ESC
Hex 1B
Decimal 27
[Range] 0 ≤ n ≤ 255
[Default] n=0
[Description] ▪ Selects the paper sensor(s) to output paper end signals when a paper end
is detected.
Bit Off/On Hex Decimal
0 Off 00 0
On 01 1
1 Off 00 0
On 02 2
2 Off 00 0
On 04 4
3 Off 00 0
On 08 8
4~7 - - -
[Note] ▪ This command is available only with a parallel interface and is ignored
with a serial interface.
ESC c 4 n
[Name] Select paper sensor(s) to stop printing.
[Format] ASCII ESC
Hex 1B
Decimal 27
[Range] 0 ≤ n ≤ 255
[Default] n=0
[Description] ▪ Selects the paper sensor(s) to use to stop printing when a paper end is
detected.
Bit Off/On Hex Decimal
0 Off 00 0
On 01 1
1 Off 00 0
On 02 2
2~7 - - -
c 3 n
63 33 n
99 51 n
Function
Paper roll near-end sensor disable.
Paper roll near-end sensor enable.
Paper roll near-end sensor disable.
Paper roll near-end sensor enable.
Paper roll end sensor disable.
Paper roll end sensor enable.
Paper roll end sensor disable.
Paper roll end sensor enable.
Reserved.
c 4 n
63 34 n
99 52 n
Function
Paper roll end sensor disable.
Paper roll end sensor enable.
Paper roll end sensor disable.
Paper roll end sensor enable.
Reserved.
53