Communication Speed - Panasonic WJ-SX550A Operating Instructions Manual

27. Communication Speed

This table is used to set the Communication Parameters between the System Controllers (or PCs) and the Matrix Switcher.
e
1. Move the cursor to the 3 position by moving the Joystick Controller, then press the Set (SET) Key.
2. Move the Cursor to the 4 position by moving the Joystick Controller.
5
Press the Function (F4) Key to open the Pop Up Window, select the desired Baud Rate by moving the Joystick Controller and
pressing the Set (SET) Key to execute the selection.
3. Move the Cursor to the 5 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Wait Time by moving the Joystick Controller and
pressing the Set (SET) Key to execute the selection.
4. Move the Cursor to the 6 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Data Bit by moving the Joystick Controller and
pressing the Set (SET) Key to execute the selection.
5. Move the Cursor to the 7 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Parity Check by moving the Joystick Controller
and pressing the Set (SET) Key to execute the selection.
6. Move the Cursor to the 8 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Stop Bit by moving the Joystick Controller and
pressing the Set (SET) Key to execute the selection.
7. Move the cursor to the 9 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select Address Control On or Off by moving the Joystick Controller
and then pressing the Set (SET) Key to execute the selection.
8. Move the cursor to the 10 position by moving the Joystick Controller.
Enter the desired Unit Number, 1-16, by pressing the Numeric Keys and then pressing the Set (SET) Key to enter the Unit
Address.
9. Repeat the above procedures until the table is completed.
10. When all settings are completed, press the Escape (ESC) Key to escape from the programming mode. The cursor returns to
the 3 position.
q w
S e t U p S y s t e m S p e e d
C o m m u n i c a t i o n S p e e d
B a u d W a i t D a t a
R a t e T i m e
C U 1 1 2 0 0 1 0 0
C U 2 1 2 0 0 1 0 0
C U 3 1 2 0 0 2 0 0
C U 4 2 4 0 0 1 0 0
C U 5 4 8 0 0 3 0 0
C U 6 9 6 0 0 3 0 0
C U 7 1 2 0 0 5 0 0
C U 8 2 4 0 0 1 0 0
A L 1 2 0 0 1 0 0 0
9 6 0 0 N o n e
P C
U n i t N o . 1
r t !0
F 1 : - - F 2 : - -
P a r i t y S t o p F l o w
B i t C h e c k B i t
8 N o n e 1
8 N o n e 1
8 N o n e 1
8 N o n e 1
8 N o n e 1
8 N o n e 1
8 N o n e 1
8 N o n e 1
8 N o n e 1
7
o d d 2
y u i
F 3 : - -
-90-
A d d r e s s
C o n t r o l C o n t r o l
N o n e N o n e
N o n e N o n e
N o n e N o n e
N o n e N o n e
N o n e N o n e
N o n e N o n e
N o n e N o n e
N o n e N o n e
N o n e N o n e
R S / C S O f f
o
F 4 : P o p U p