Timer Event Schedule - Panasonic WJ-SX550A Operating Instructions Manual

8. Timer Event Schedule

This table is used to enable and disable Tour and Group Sequences according to the time of day and day of the week.
There are 45 events available in one day.
q
S e t U p
t
T i m e r
S t a r t
0 0 : 0 0
0 0 : 3 0
1 0 : 0 0
1 0 : 1 0
1 1 : 0 0
1 1 : 0 0
1 1 : 3 0
1 1 : 5 0
1 2 : 0 0
1 2 : 3 0
1 3 : 3 0
1 5 : 0 0
1 6 : 0 0
1 7 : 0 0
1 7 : 3 0
y u
F 1 : N e x t
To programme or edit a Timer Event Schedule do the following:
1. Move the cursor to the 5 position by moving the Joystick Controller, and then press the Set (SET) Key.
2. Move the cursor to the 6, 7, 8 or 9 position by moving the Joystick Controller.
Enter the desired hours (military time) or minutes by pressing the Numeric Keys.
3. Move the cursor to the 11 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window.
Select the desired sequence type by moving the Joystick Controller, then enter the sequence number by pressing the
Numeric Keys. Next, press the Set (SET) Key to execute the selection.
Note: The 11 position consists of nine monitor selections.
4. Move the cursor to the 12 position by moving the Joystick Controller.
By pressing the Set (SET) Key repeatedly, access to higher number monitors is possible.
5. Move the cursor to the 10 position by moving the Joystick Controller.
By pressing the Set (SET) Key repeatedly, access to lower number monitors is possible.
6. When satisfied with the programming of events on this page, press the Function (F1) Key to select the next page. Repeat the
above procedures until all events are programmed.
Note: As there is a total of 45 events available for a day and each page holds 15 events, there is a total of 3 pages available
for each day.
7. Press the Function (F2) Key to go back to the previous page.
8. When satisfied with all events, press the Escape (ESC) Key to escape from the programming mode, programmed events are
displayed in chronological order and the cursor returns to the 5 position.
9. Similarly, repeat the above procedures to programme other days.
Notes:
• When programming an event that extends into the next day, divides the event into two separate events and program both
events separately.
• The sequence, that is activated by the programmed timer, will be continued until the other operation is made after the
Stop time.
w e
P R O G . T i m e r
E v e n t S c h e d u l e
S t o p < M 1 M 2 M 3
0 1 : 0 0 T 6 4
0 9 : 0 0
1 0 : 1 0 T 1 7
1 0 : 5 0 G 1 G 1 G
1 1 : 3 0
1 1 : 4 0
1 1 : 5 0
1 2 : 0 0
1 2 : 3 0
1 3 : 3 1
1 4 : 3 0
1 6 : 0 0
1 7 : 0 0 T 2 1
1 7 : 3 0
1 9 : 0 0
i o !0 !1
P a g e F 2 : P r e P a g e
r
E v e n t S U N .
M 4 M 5 M 6 M 7
T 0 1 T 0 1
1 G 1 T 3 6
T 0 1 T 3 2
T 0 8
T 1 1
T 4 3
T . . T o u r
F 3 : D E L F 4 : P o p
-73-
P a g e 1 o f 3
M 8 M 9 >
G 3 G 3
T 5 2
!2
G . . G r o u p
U p
5