Tension / Torque Setting - Mitsubishi Electric LE-50PAU Instruction Manual

4.3 Tension / torque setting

Similarly to description given on page 31, [ 張力 / トルク ] key is acceptable from any screen condition on the
screen displayed prior to power failure after turning on the power source.
Ａ Ｄ Ｊ Ｕ Ｓ Ｔ
張力
トルク Ｓ Ｅ Ｔ ＊
▲
Ｄ Ｉ Ａ Ｍ Ｎ Ｔ
Ｔ Ａ Ｐ Ｍ Ｎ Ｔ
▼
Ｓ Ｐ ＊ ＊ ＊ ％
Ｖ Ｒ ＊ ＊ ＊ ％
▲ ▼
Set display [ ]
to line of [ SET ]
▲ ▼
Set display [ ]
to line of [ ADJUST ]
Reset setting mode
セ ッ テ イ
Ｓ Ｅ Ｔ Ｔ Ｎ Ｇ
< ADJUST (adjustment) >
The cursor key after pressing the [ 設定 ] key functions to increase / decrease the numeric.
•
The numeric is increased / decreased each time when the [INC ] key or [DEC ] key is pressed.
If such key is pressed continuously, the numeric is incerased / decerased at high speed.
Such numeric increase / decrease is valid even if the [ 実行 ] key is not presse.
When necessary to reset hte setting mode, press the [ 実行 ] key or [ クリア ] key.
When the numeric is input, such input numeric is validated when the [ 実行 ] key is pressed.
•
If the numeric other than 0 ~ 100% is input, however, it is not accepted, but error message is displayed.
In such a case, press the [ クリア ] key and input the correct numeric.
The value adjusted can be also displayed by bar graph.
•
When the SET is set to "0", the ADJUST displays "0%" and the setting will not be changed.
If any power failure occurs, the value of ADJUST is saved from RAM to EEPROM memory.
•
< MNT (monitor) >
DIA MNT displays the result of winding diameter calculated, while TAP MNT displays the current taper
•
ratio.
SP is used to monitor the input voltage ( 8V = 100% ), using the external variable resistor, while VR to
•
monitor the adjustment value ( V = 100% ) using the built-in variable resistor. 0% is displayed for invalid
side.
TRQ displays the current output with full-scale at 100%.
•
When the non-linearity compensation is executing, it is output as torque conversion value.
When the [ 張力 / トルク ] key is pressed, and then the [DEC ] key two times, the screen is changed to
•
DIA MNT, TAP MNT screen. When the [DEC ] key is further pressed, the screen is changed to SP, VR,
TRQ screen.
＊ ＊ ＊ ％
bar graph
＊ ＊ ＊ ＊ ｍ ｍ φ
＊ ＊ ＊ ％
Ｔ Ｒ Ｑ
＊ ＊ ＊ ％
０ １
or
設定
実行
Correction
▲ ▼
設定
Numeric value
increment / decrement
クリア
Correction
エ ラ －
Ｅ Ｒ Ｒ Ｏ Ｒ
---------- SET=1
When the [ 張力 / トルク ] key is pressed, the
•
screen as shown at left is displayed, in which
the line or screen changeover is executable,
using cursor keys ( , ).
The screen without "
monitor screen.
When it is set to "0", the built-in variable resis-
•
tor is invalidated ( external variable resistor is
validated ), and when it is set to "1", the built-
in variable resistor is validated ( external vari-
able resistor is invalidated ).
実行
Error
33
" mark indicates the