Toro 22322 Operator's Manual page 5

•
Ensure that the area is clear of other people before
operating the traction unit. Stop the traction unit if
anyone enters the area.
•
Never leave a running traction unit unattended. Always
lower the loader arms, shut off the engine, set the parking
brake, and remove the key before leaving.
•
Do not exceed the rated operating capacity, as the traction
unit may become unstable which may result in loss of
control.
•
Do not carry a load with the arms raised. Always carry
loads close to the ground.
•
Do not over-load the attachment and always keep the
load level when raising the loader arms. Logs, boards, and
other items could roll down the loader arms, injuring you.
•
Never jerk the controls; use a steady motion.
•
Watch for traffic when operating near or crossing
roadways.
•
Do not touch parts which may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service.
•
Check for overhead clearances (i.e., branches, doorways,
electrical wires) before driving under any objects and do
not contact them.
•
Ensure that you operate the traction unit in areas where
there are no obstacles in close proximity to the operator.
Failure to maintain adequate distance from trees, walls,
and other barriers may result in injury as the traction unit
backs up during operation if the operator is not attentive
to the surroundings. Operate the unit only in areas where
there is sufficient clearance for the operator to safely
maneuver the product.
•
Before digging, have the area marked for underground
utilities, and do not dig in marked areas.
•
Locate the pinch point areas marked on the traction unit
and attachments and keep hands and feet away from
these areas.
•
Before operating the traction unit with an attachment,
ensure that the attachment is properly installed.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
Slope Operation
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or death.
All slopes require extra caution.
•
Do not operate the traction unit on hillsides or slopes
exceeding the angles recommended in
7), and those in the attachment Operator's Manual. See also
the Slope Indicator (page
•
Operate up and down slopes with the heavy end of
the traction unit uphill. Weight distribution changes.
An empty bucket makes the rear of the traction unit
the heavy end, and a full bucket makes the front of the
Stability Data (page
8).
traction unit the heavy end. Most other attachments make
the front of traction unit the heavy end.
•
Raising the loader arms on a slope affects the stability of
the machine. Whenever possible, keep the loader arms in
the lowered position when on slopes.
•
Do not remove or add attachments on a slope.
•
Remove obstacles such as rocks, tree limbs, etc. from the
work area. Watch for holes, ruts, or bumps, as uneven
terrain could overturn the traction unit. Tall grass can
hide obstacles.
•
Use only Toro-approved attachments. Attachments can
change the stability and the operating characteristics of
the traction unit. Warranty may be voided if used with
unapproved attachments.
•
Keep all movements on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Avoid starting or stopping on a slope. If the traction unit
loses traction, proceed slowly, straight down the slope.
•
Avoid turning on slopes. If you must turn, turn slowly
and keep the heavy end of the traction unit uphill.
•
Do not operate near drop-offs, ditches, or embankments.
The traction unit could suddenly turn over if a track goes
over the edge of a cliff or ditch, or if an edge caves in.
•
Do not operate on wet grass. Reduced traction could
cause sliding.
•
Do not park the traction unit on a hillside or slope.
Maintenance and Storage
•
Park the machine on level ground, disengage the auxiliary
hydraulics, lower the attachment, set the parking brake,
shut off the engine, and remove the key. Wait for all
movement to stop before adjusting, cleaning, or repairing.
•
Clean debris from attachments, drives, mufflers, and
engine to help prevent fires. Clean up oil or fuel spills.
•
Let the engine cool before storing and do not store near
flame.
•
Do not store fuel near flames or drain indoors.
•
Never allow untrained personnel to service the machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect the battery before making any repairs.
Disconnect the negative terminal first and the positive
last. Connect positive first and negative last.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Charge batteries in an open, well-ventilated area, away
from spark and flames. Unplug the charger before
connecting or disconnecting it from the battery. Wear
protective clothing and use insulated tools.
5