Page 1
To prevent accidents and/or machine damage, read these instructions before installation or use. Use the dryer only as instructed in this owner’s guide and installation instructions manual included with your dryer. Keep this guide for future reference Front-Loading Dryer DV 16540 NBL00 Owner’s Guide & Installation Instructions...
Please read this manual first! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through strict quality control procedures, will give you the best results. Therefore, we advise you to read this manual thoroughly before using your product and keep it for future reference.
TABLE OF CONTENTS 1 Your Dryer Overview ...5 2 Important Safety Instructions 3 Installation Instructions Electrical connection ...8 Grounding Instructions ...9 Appropriate installation location ...9 Minimum Installation Clearances ...10 Use on top of a washing machine ...10 Adjusting the feet ...11 Ventilation duct and connection ...11 Destroying packaging material ...12 4 Operating Instructions...
Overview Figure 1 Type label Control Panel Specifications of this appliance may change without notice to improve the quality of the product. Drawings in this manual are schematic and may not match your product exactly. Values stated on the machine labels or in the documentation accompanying it are obtained in the laboratory in accordance with relevant standards.
Important Safety Instructions WARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow the basic precautions including the following: • Read all instructions before using the appliance. Otherwise, there may be the risk of personal injury or material damage. Additionally, any warranty and reliability commitment will become void.
Page 7
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber- backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer. • Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
Installation Instructions A WARNING - Risk of fire • The clothes dryer (“appliance‘) installation must be performed by a qualified installer. • Install the appliance according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials.
8. Attach the power cord Ground conductor (the center wire) to the terminal labeled N. Connect the terminal labeled N and the Ground terminal labeled G with the supplied short cable. Tighten the terminals so that they securely hold the conductors. 9.
Minimum Installation Clearances Alcove or Built-under Closet Sides 1/2” (12.5 mm) 1” (25 mm) Rear 1” (25 mm) ” (875 mm) min. ” Ventilation Requirements Closet door must have 2 openings, located 3 inches (7.5 cm) from bottom and top of door each having a minimum area of 60 sq.
when they are full. Therefore, the floor must be capable of carrying the load placed on it! Adjusting the feet In order to ensure that your appliance operates more silently and vibration-free, it must stand level and balanced on its feet. The front feet of the appliance can be adjusted.
Destroying packaging material Packaging material can be dangerous to children. Keep the packaging materials out of the reach of children or dispose of them accordingly. Do not dispose of them together with normal domestic waste. Packaging materials of your appliance are manufactured from recyclable materials.
Operating Instructions WARNING:To reduce the risk of fire, electric shock, or personal injury, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. A B C o p q First Use • When operating your machine for the first time check inside the drum for any foreign objects.
Correct load capacity Please consult the information in the “Program Selection” section. Always start the program in accordance with the maximum load capacity. Adding laundry to the dryer over the level shown in the figure is not recommended. Drying performance will be reduced when the machine is overloaded.
Loading door • Open loading door. • Place laundry items loosely into the dryer. • Push the loading door to close. Make sure that no items are caught in the door. Turning on the dryer Prepare dryer for program selection by pressing the ìOn/Offî...
Special programs For special cases, there are also extra programs available: Permanent Press Regular Damp Mixed Fabric Timed Programs 15 min 30 min 75 min Additional programs may differ according to the model of your dryer. •Automatic Dry / Mixed Fabric (max. 3 kg) Mix program (Regular Dry) is for mixed loads with different types of fabrics.
Starting the Program 1. Press the “Start/Pause/Cancel” button to start the program. 2. The ìStart/Pause/Cancelî button will light up to indicate that the program has started. Progress of program Progress of a running program is shown through the program follow-up indicator. At the beginning of each program step, the related lamp will light up and the lamp of the completed step will turn off.
Child-proof lock There is a childproof lock to prevent any program interruption due to the pressing of keys while a program is running. The loading door and all buttons except the “On/Off” key on the panel are deactivated when the child- proof lock is active.
Technical Specifications Enus Model Height (in) Witdth (in) Depth (in) Height adjustment of feet (in) Weight, unpacked (lbs) Voltage / Frequency Connected load Fuse This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off at recycling locations provided for this purpose. Your appliance also contains a large amount of recyclable material.
Quick Start-up Instructions Open loading door. Check filter. Load laundry loosely into the drum. Push loading door closed. Ensure no items are caught in the door. Push the ON / OFF button to ON. Cottons/Regular Extra Regular Damp Delicates Refresh Select the appropriate Program.
Maintenance and cleaning Lint filter Lint and fibers released from the laundry in to the air during the drying cycle are collected in the “Lint Filter”. ibres and lint are formed during wearing and washing. Always clean the filter after each drying cycle.
Troubleshooting Problem Cause Drying process Lint filter may not have been takes too long. cleaned. * It may not plugged in. * The loading door may be ajar. Dryer does not * Program may not be set or the switch on or the “Start/Pause/Cancel”...