Rider Information Display; Rider Information Display (Intl) - Polaris GENERAL 2016 Service Manual

RIDER INFORMATION DISPLAY

The rider information display is located in the instrument
cluster. All segments will light up for 1 second at start-up.
NOTICE
If the instrument cluster fails to illuminate, a battery
over-voltage may have occurred and the instrument
cluster may have shut off to protect the electronic
speedometer.
1. Vehicle Speed Display - Analog display of vehicle
speed in MPH or km/h.
2. Information Display Area - Odometer / Trip Meter /
Tachometer / Engine Temperature / Engine Hours
/ Service Info / Clock - LCD display of the service
hour interval, total vehicle miles or km., total engine
hours, a trip meter, engine RPM and engine
temperature.
3. MPH / KM/H Display - MPH is displayed when the
instrument cluster is in the Standard mode. KM/H is
displayed when the instrument cluster is in the Metric
mode.
4. High Beam Indicator - LED icon illuminates
whenever the headlight switch is in the high beam
position.
5. Fuel Level Indicator - LCD bar graph indicating
current fuel level.
6. Clock - Displays current time in either 12-hour or 24-
hour formats.
7. Engine Temperature Indicator - Illuminates when
the ECU determines the engine is overheating. The
indicators will initially flash to indicate the engine is
overheating. The indicators will stay lit and not flash if
a severe overheating condition exists.
8. Service Interval Indicator - Preset at the factory and
adjustable by the user, a flashing wrench symbol
alerts the operator that the preset service interval has
been reached and maintenance should be performed.
The wrench icon will flash for 10 seconds upon start-
up once it reaches 0.
9. Check Engine MIL - Illuminates when the ECU has
detected a Diagnostic Trouble Code in the engine
management system.
10. AWD Indicator - Illuminates when the AWD / TURF
switch is in the AWD position.
11. Neutral Gear Indicator - Illuminates when gear
selector is in the neutral (N) position.
9929375 R02 - 2016-2019 GENERAL / GENERAL 4 Service Manual
© Copyright Polaris Industries Inc.
12. Gear Position Indicator - Displays gear selector
position.
H = High
L = Low
N = Neutral
R = Reverse
P = Park
– = Gear Signal Error (shifter stuck between gears)
13. Power Steering System MIL - Illuminates when a
fault has occurred with the power steering system.
This indicator illuminates when the key is turned to
the ON position and goes off when the engine is
started.
14. Turn Signal / Hazard Lamp Indicator - Illuminates
whenever the LH, RH or hazard lamps are activated
(INT'L Models Only).
15. Helmet / Seat Belt Indicator - Illuminates for several
seconds when the key is turned to the ON position.
The lamp is a reminder to the operator to ensure all
riders are wearing helmets and seat belts before
operating the vehicle.
16. ADC Indicator - Illuminates when Active Descent
Control (ADC) is selected.
17. Performance Limited Indicator - Illuminates when
engine performance is electronically limited.
18. Low Fuel Indicator - Illuminates when fuel level
reaches lowest bar on fuel level indicator.
19. Engine Speed Display - Analog display of engine
speed in thousands of revolutions per minute.
20. Parking Brake Indicator - Illuminates when parking
brake is engaged (INT'L Models Only).
21. Low Battery Indicator - Illuminates when battery
voltage drops below 8.5 Volts.

RIDER INFORMATION DISPLAY (INTL)

The rider information display is located in the instrument
cluster. All segments will light up for 1 second at start-up.
NOTICE
If the instrument cluster fails to illuminate, a battery
over-voltage may have occurred and the instrument
cluster may have shut off to protect the electronic
speedometer.
1. Vehicle Speed Display - Analog display of vehicle
speed in MPH or km/h.
ELECTRICAL
11
11.31