Ftp Access Via Ms-Dos - ABB SM1000 User Manual

Videographic Recorders
SM1000 and SM2000

3.3.1 FTP Access via MS-DOS

To use FTP access:
1. If the DOS window is not open, click the 'Start' button on
the task bar and select 'Run'.
2. In the 'Open:' field, type 'cmd' and click the 'OK' button.
A DOS window is displayed with the cursor at the default
drive prompt.
3. Type 'ftp' and press Enter. The ftp prompt is displayed.
4. Type 'open' followed by the IP address assigned to the
instrument and press Enter. If connection is successful, a
confirmation message is displayed, e.g. the following is
displayed for a device with IP address 192.168.1.1:
Connected to 192.168.1.1
220 WinCE GkWare FTP Service (Version 1.3 May 6 2003)
User (192.168.1.1: (none):
5. Enter the FTP User name for the instrument (see Section
3.1, page 5) and press Enter. The following is displayed:
331 OK, password required
Password:
Note. Users with read-only access cannot proceed
beyond this point and a password is not required.
6. Type the device password and press Enter. The following
is displayed:
230 OK
ftp>
Note.
When typing the password, the cursor does not
move and nothing appears in the DOS window.
An audit log entry is created for each FTP logon
giving details of the logon user name and type of
access (full or read-only), e.g:
The link is now open.
IM/SMENET Issue 4
The following FTP commands are used to communicate with the
instrument:
Cd Change directory on the server
Close Terminate the data connection
Del Delete a file on the server
Dir Display the server directory
Get Get a file from the server
Help Display help
Ls Lists contents of the remote directory
Mget Get several files from the server
Mput Send several files to the server
Open Connect to the server
Put Send a file to the server
Pwd Display the current server directory
Quote Supply an internal FTP command directly
Quit Terminate the FTP session
For example, to view the contents of the root directory, type 'dir'
at the ftp prompt and press Enter. A list of folders is displayed:
ftp> dir
200 PORT command successful.
150 Opening ASCII mode data connection for /bin/ls.
01-01-1998 00:00AM<DIR>Flash_Disk
01-01-1998 00:00AM<DIR>Storage_Card
11-05-2001 02:45PM<DIR>www
11-05-2001 02:45PM<DIR>My Documents
11-05-2001 02:45PM<DIR>Program Files
11-05-2001 02:45PM<DIR>Temp
11-05-2001 02:45PM<DIR>Windows
226 Transfer complete.
ftp: 188 bytes received in 1.07 seconds (0.18Kbytes/sec)
To view the contents of a folder, type 'cd [Folder Name]' and
press Enter, then type 'dir' and press Enter. A similar list is
displayed showing the contents of the folder.
Note. The contents of the Storage_Card folder are
accessible only if archiving is set to 'On-line' in the
instrument's Setup menu – see Section 3.3 of the relevant
User Guide (IM/SM1000 or IM/SM2000).
To copy a file from the instrument to the PC's local or network
drive, type:
get '[File Name]'
...at the ftp prompt and press Enter. A confirmation such as the
following is displayed:
ftp> get'10_00 051101Process Group 1.D00'
200 PORT command successful.
150 Opening ASCII mode data connection for 10_00
051101Process Group 1.D00
226 RETR command successful.
ftp: 11876 bytes received in 0.70Seconds 16.94
Kbytes/sec.
ftp>
3 Configuration
7