Hitachi FL.NET User Manual page 208

No. Error code
41 7D18 Module error (TASK-ROM CHECKSUM
ERROR)
42 010B Parameter type Mismatch (It is setted for
S10mini)/ROM3 checksum error
43 D010 Module error (Memory Alarm)
44 D330 Module error (Hardware WDT timeout)
45 D340 Module error (Software WDT Timeout)
46 D810 System down (BPU Error)
47 3389 System down (FP Unavailable)
48 30F9 System down (Illegal Exception)
49 5700 System down (System Error)
50 5800 System down (Kernel Trap)
51 7308 I/O error (SEND_TIMEOUT)
52 730A I/O error (RESET_ERROR)
53 730E I/O error (MEMORY)
54 7310 I/O error (LOSS)
55 7311 I/O error (RETRY)
56 7312 I/O error (LATE)
57 7351 I/O error (TX_ABORT)
58 7353 I/O error (TX_DEFER)
59 7370 I/O error (EC_PCI_ERROR)
60 7376 I/O error (TX_DATA_UNDER)
61 7375 I/O error (RX_STAT_OVER)
62 7377 I/O error (RX_DATA_OVER)
63 0113 I/O error (IP_ADDERSS_NOT_REGISTERED) IP address not set yet
64 7400 I/O error (PCI_BUS_ERR)
65 7505 I/O error (INV_INTR)
66 7508 I/O error (BUF_OVF)
67 750F I/O error (SOCKET_OVF)
68 7510 I/O error (IFCONFIG_UP)
69 7512 I/O error (IPADDR_DUPL)
70 0200 Network participation not completed.
71 0201 Duplicate common memory settings
72 0202 Duplicate node numbers
73 0203 FL.NET module setting error
74 0204 Token hold timeout
Table 7-2 Error Messages (2/2)
Error message
ROM checksum error (communication
task)
ROM3 checksum error (communication
parameter)
Memory single-bit error (solid)
Hardware watchdog timer timeout
Software watchdog timer timeout
BPU error
Floating-point unavailability exception
Illegal-exception error
System down (system error)
System down (kernel trap)
Transmission timeout error
Hardware resetting error
Memory error
Carrier loss error
Retry error
Late-collision error
Abnormal end of transmission
Transmission error due to transmission
delay
PCI error detected in communication LSI
Communication data FIFO underrun
Reception-status FIFO overrun
Received-data FIFO overrun
PCI bus error
Invalid interrupt generated from the
communication line
OS-managed send/receive buffer
overflowed.
Socket table is full.
Network interface initialization error
Duplicated-IP address error
The FL.NET module currently not
participating in the network
The local node's common memory
setting overlaps with another distant
node's common memory setting.
Another distant node uses the same node
number as the local node in the same
network.
The FL.NET module's setup is
erroneous.
The defined token hold time was
exceeded three times consecutively.
LER
Meaning
LED
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Turned on
–
Turned on
Turned on
Turned on
7-9
7 TROUBLESHOOTING
ERR
Required recovery action
LED
Turned on Hardware item replacement
Turned on Communication parameter re-
setting
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Hardware item replacement in
case it is not recovered along with
power recovery.
Turned on Hardware item replacement in
case it is not recovered along with
power recovery.
Turned on Hardware item replacement in
case it is not recovered along with
power recovery.
– Transmission path checkup (*1)
– Transmission path checkup (*3)
– Transmission path checkup (*5)
– Transmission path checkup
– Transmission path checkup
Turned on Hardware item replacement (*6)
– Transmission path checkup (*6)
– Check the load on the
communication line. (*6)
– Check the load on the
communication line. (*7)
Blinking Register the IP address.
Turned on Hardware item replacement
Turned on Hardware item replacement
Turned on Check the load on the
communication line. (*2)
– Check the load on the
communication line.
Turned on Review the settings made.
Turned on Review the settings made. (*4)
– Connect it to the network.
Blinking The local node's common
memory setting is zero (0).
Disconnect the local node from
the network and set common
memory again.
Blinking Change either of the duplicated
node numbers so that they will be
unique in the network.
Blinking By using the setup tool, check the
setup for error and correct the
error. If this action does not
solve the problem, replace the
module with a new one.
– Hardware item replacement