Mitsubishi Electric FR-A820-00046 Instruction Manual page 222

Parameter List
Pr.
Pr. Name
group
Encoder signal loss detection
C148
376
enable/disable selection
Lq tuning target current adjustment
C150 1002
coefficient
Starting resistance tuning
C182 717
compensation
Starting magnetic pole position
C185 721
detection pulse width
C200 450 Second applied motor
C201 453 Second motor capacity
C202 454 Number of second motor poles
C203 51 Rated second motor current
C204 456 Rated second motor voltage
C205 457 Rated second motor frequency
C206 743 Second motor maximum frequency
C207 744 Second motor inertia (integer)
C208 745 Second motor inertia (exponent)
Second motor auto tuning setting/
C210 463
status
C211 574 Second motor online auto tuning
C220 458 Second motor constant (R1)
C221 459 Second motor constant (R2)
Second motor constant (L1) / d-shaft
C222 460
inductance (Ld)
Second motor constant (L2) / q-shaft
C223 461
inductance (Lq)
C224 462 Second motor constant (X)
C225 455 Second motor excitation current
Second motor torque current/Rated
C226 860
PM motor current
Second motor induced voltage
C230 738
constant (phi f)
C231 739 Second motor Ld decay ratio
C232 740 Second motor Lq decay ratio
Control terminal option-Number of
C240
851
encoder pulses
Control terminal option-Encoder
C241
852
rotation direction
C242 Encoder option selection
862
Control terminal option-Signal loss
C248
855
detection enable/disable selection
Second motor protection current
C233 746
level
Second starting resistance tuning
C282 741
compensation
Second motor magnetic pole
C285 742
detection pulse width
Tab. 5-12: Motor constant parameters (2)
5 - 42
(A) Application parameters
Refer to
page
Parameters to set a specific application.
5-469
Pr.
Pr.
group
5-454
A000 135
5-454
A001 136
5-454
A002 137
A003 138
5-434
5-440,
A004 139
5-454
5-440,
A005 159
5-454
5-292,
A006 248
5-440,
5-454
A007 254
5-440,
A100 278
5-454
A101 279
5-440,
5-454
A102 280
5-454
A103 281
5-454
A104 282
5-454
A105 283
5-440,
5-454
A106 284
5-465
5-440, A107 285
5-454
A108 639
5-440
A109 640
5-440,
5-454
A110 292
5-440,
5-454
A120 642
5-440
A121 643
5-440
5-440,
A122 644
5-454
A123 645
5-454
A124 646
5-454
A125 647
5-454
A126 648
2-73
A128 650
2-73
A129 651
5-64
A130 641
5-469
5-454
A200 270
5-454
A201 271
5-454
A202 272
A203 273
A204 274
Tab. 5-13:
Name
Electronic bypass sequence
selection
MC switchover interlock time
Start waiting time
Bypass selection at a fault
Automatic switchover frequency
from inverter to bypass operation
Automatic switchover frequency
range from bypass to inverter
operation
Self power management selection
Main circuit power OFF waiting time
Brake opening frequency
Brake opening current
Brake opening current detection
time
Brake operation time at start
Brake operation frequency
Brake operation time at stop
Deceleration detection function
selection
Overspeed detection frequency
Brake opening current selection
Brake operation frequency selection
Automatic acceleration/deceleration
Second brake opening frequency
Second brake opening current
Second brake opening current
detection time
Second brake operation time at start
Second brake operation frequency
Second brake operation time at stop
Second deceleration detection
function selection
Second brake opening current
selection
Second brake operation frequency
selection
Second brake sequence operation
selection
Stop-on contact/load torque high-
speed frequency control selection
High-speed setting maximum
current
Middle-speed setting minimum
current
Current averaging range
Current averaging filter time
constant
Application parameters (1)
Parameters
Refer to
page
5-471
5-471
5-471
5-471
5-471
5-471
5-480
5-480
5-484
5-484
5-484
5-484
5-484
5-484
5-484
5-118,
5-484
5-484
5-484
5-255,
5-260,
5-484
5-484
5-484
5-484
5-484
5-484
5-484
5-484
5-484
5-484
5-484
5-489,
5-494
5-494
5-494
5-494
5-494