Specifications; Dimensions And Weights (Approx.); Optional Equipment - Toro 07052 Operator's Manual

Specifications

Note: Specifications and design are subject to change without notice.
Machine Drive
Frame
Hitch (Model 07050)
Hitch (Model 07052)
Fan
Fan Drive (Model 07050)
Fan Drive (Model 07052)
Hopper
Flex Tip Reel
Flex Tip Reel Drive
(Model 07050)
Flex Tip Reel Drive
(Model 07052)
Dimensions and Weights
(approx.)
Width
Height
Length
Empty Weight
(Model 07050): Kohler, 4 cycle air cooled 22 H.P. engine @ 3600 rpm, 41.1 cu. in.
(674 cc) displacement. Oil capacity is 4 pints w/filter. Mechanical fuel pump. Gas
tank capacity is 4 gallons.
(Model 07052): Powered by Power Take Off drive from prime mover–540 RPM.
All welded structural rectangular 11 ga. tubing.
Pin–type, 3/4" dia. vertically adjustable in 1" increments.
Pin–type, 3/4" dia. three vertical positions for tractor hitches ranging from 7–1/4" to
17–1/4" in height.
Centrifugal type–double inlet; 4 blade, 16" wide, 23–14" diameter, 3/16" thick, high
tensile steel. Shaft mounted in self–aligning, sealed ball bearings. Blower inlet area
is 286 sq. in., blower discharge area is 255 sq. in. Twin fan hood construction for
uniform air distribution: 4–1/2" deep x 63" wide (inlet area–283 sq. in.); variable
position from weighted rubber flap.
Banded double drive belt direct from drive shaft to fan impeller drive shaft with
driver pulley, fan with driven pulley. Fan impeller runs at 1580 R.P.M. (tip speed
9100 ft./min.) at 3250 engine R.P.M.
Banded double drive belt direct from drive shaft to fan impeller drive shaft with
driver pulley, fan with driven pulley. Fan impeller runs at 1490 R.P.M. (tip speed
9100 ft./min.) with 540 PTO R.P.M.
5–3/4 cu. yd. volume; 18 gauge top section with 16 gauge bottom section–rib
reinforced; full width self cleaning semi–automatic dumping.
Forward spinning with 6 rows of teeth. All steel construction with replaceable nylon
teeth; each row containing 11 individually spring–loaded flexible sets, 552 teeth
total; shaft set in self–aligning sealed bearings. Reel supported by adjustable
counter balance springs and adjustable gauge wheels. Gauge wheels are steel
construction with non–scuffing rubber tires and sealed ball bearings; infinitely
adjustable vertically.
Banded double drive belt from engine pulley to jackshaft pulley; belt from jack shaft
(driver) pulley to flex tip reel (driven) pulley. Flex tip runs at 275 R.P.M. (tip speed
1355 ft./min.) at 3250 engine R.P.M.
#60 roller chain from 40 tooth side shaft sprocket to 29 tooth jackshaft sprocket.
Belt jack shaft (driver) pulley flex tip reel (driven) pulley. Flex tip runs at 260 R.P.M.
(tip speed 1,230 ft./min.) with 540 R.P.M.
85–1/2"
79–1/2"
13' 3" (Model 07050)
14' (Model 07052)
2160 lb. (Model 07050)
1980 lb. (Model 07052)

Optional Equipment

Hard Surface Brush Kit
Thatching Reel Kit
Flex Tip Reel
Spark Arrester Muffler
*
Contact Your Local Kohler Dealer
*
7
Model No. 07162
Model No. 07178
Model No. 07164
Kohler No 1218902