1. Manuals
  2. Brands
  3. Toro Manuals
  4. Blower
  5. RAKE-O-VAC 07050
  6. Operator's manual

Toro 07050 Operator's Manual

66" rake-o-vac
Hide thumbs Also See for 07050:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Form No. 3362–316 Rev A
66" Rake–O–Vac Sweeper
Model No. 07050–240000201 and up
Operator's Manual
Domestic English (EN)

Advertisement

Table of Contents
loading

Related Manuals for Toro 07050

Summary of Contents for Toro 07050

  • Page 1 Form No. 3362–316 Rev A 66” Rake–O–Vac Sweeper Model No. 07050–240000201 and up Operator’s Manual Domestic English (EN)

  • Page 2: Table Of Contents

    ......Removing Sweeper From Prime Mover ..The Toro General Commercial Products Warranty . . . W 2009 by The Toro Company...

  • Page 3: Introduction

    Authorized Service Although hazard control and accident prevention Dealer or Toro Customer Service and have the model and partially are dependent upon the design and serial numbers of your product ready. Figure 1 illustrates...

  • Page 4: While Operating

    Reduce speed when making sharp turns or • Do not overspeed engine by changing governor settings. when turning on hillsides. To assure safety and accuracy, have an Authorized Toro Distributor check maximum engine speed with a – Avoid sudden stops and starts.

  • Page 5: Safety And Instruction Decals

    Replacement parts and accessories made by other manufacturers could be dangerous. Such use could void the product warranty of The Toro Company. Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
  • Page 6 92-8309 93-4041...

  • Page 7: Specifications

    Dimensions and Weights (approx.) Width 85–1/2” Height 79–1/2” Length 13’ 3” Empty Weight 2160 lb. (Model 07050) Optional Equipment Hard Surface Brush Kit Model No. 07162 Thatching Reel Kit Model No. 07178 Flex Tip Reel Model No. 07164 Spark Arrester Muffler...

  • Page 8: Setup

    Setup Note: Determine the left and right side of the machine from the normal operating position. Description Qty. Operator’s Manual Read before operating the machine. Engine Operator’s Manual Parts Catalog Remove, Activate And Charge Warning Battery Charging the battery produces gasses that can 1.

  • Page 9: Mount Sweeper To Prime Mover

    To assure proper debris pickup, make sure sweeper frame is 1. Sweeper jack 3. Adjusting screws parallel with the ground. 2. Hitch tongue (Model 07050) 1. Position sweeper on a flat, level surface. 2. Insert sweeper jack caster wheel onto sweeper end of jack tube. Removing Sweeper From 3.

  • Page 10: Before Operating

    Before Operating 4. Pour oil into fill opening until the oil level is up to the “FULL” mark on the dipstick. Add the oil slowly and check the level often during this process. DO NOT OVERFILL Check Engine Oil Important Check level of oil every 8 operating hours or daily.

  • Page 11: Check Tire Pressure

    Use unleaded regular gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. Important Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline.

  • Page 12: Adjust Rake Depth

    Adjust Rake Depth Adjust Rubber Flap Flex tip reel should be adjusted so rake tips slightly touch For best debris pick up results, metal portion of front flap surface but do not penetrate turf. If rake tips penetrate turf, should be vertical to ground. improper debris pickup could result.

  • Page 13: Operation

    Operation Note: Determine the left and right sides of the machine from the normal operating position. Controls Flap Lever Move flap lever (Fig. 11) downward to engaged position and upward for disengaged position. Move lever to upward position when transporting machine. Figure 12 1.

  • Page 14: Starting Instructions

    Note: To maintain a straight line when sweeping, sight of an object in the foreground. • Always try to make a long, continuous run with a slight overlap on the return run. • On turf areas, the flex tip reel will pick up twigs, clippings, leaves, pine needles and cones, small debris (beverage cans, small bottles, paper plates, etc.).

  • Page 15: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Important Refer to your engine operator’s manual for additional maintenance procedures. Lubrication The Rake–O–Vac has grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. Lubricate bearings after every 30 hours of operation or whenever machine is washed with water.

  • Page 16: Changing Engine Oil And Filter

    Changing Engine Oil and Filter Servicing Air Cleaner Change oil initially after the first 5 hours of operation, 1. Release latches securing air cleaner cover to air cleaner thereafter change oil every 100 hours and filter every 200 body. Separate cover from body. Clean inside of air hours.

  • Page 17: Replacing Spark Plugs

    Replacing Spark Plugs Replace Fuel Filter Replace spark plugs or reset gap after every 200 operating Replace fuel filter after every 600 hours of operation. hours to assure proper engine performance and reduce 1. Place a clean container under fuel filter. exhaust emission level.

  • Page 18: Cleaning Blower Housing

    Cleaning Blower Housing Warning Before removing any debris from blower housing, disengage P.T.O. drive, stop engine(s) and make certain all moving parts have stopped or personal injury may occur. 1. Make sure impeller has stopped rotating before removing access plates. 2.
  • Page 19 Jackshaft Belt 2. To adjust belt tension: • Loosen (4) engine mounting bolts. 1. Check tension by depressing belt at mid span of jackshaft and clutch pulleys with 4 to 5 lbs. of force. Belt should deflect .25 in. If deflection is incorrect, proceed to next step.

  • Page 20: Pulley Removal

    Flex Tip Reel Removal • Reinstall guard. Make sure there is clearance between belt and belt guard. Removal of flex tip reel should be done on a hard and level surface. 1. Raise front of sweeper as high as possible by lowering jack.

  • Page 21: Flex Tip Rake Rod Or Finger Plate Replacement

    6. Slide Thatcher into position and secure to reel support Note: Spacers should be re–installed whenever the thatcher arms. is removed and either the brush or flex tip reel is mounted to sweeper. 7. Align idler sprocket with jackshaft sprocket and thatcher sprocket.

  • Page 22: Flex Tip Rake Tine Replacement

    Flex Tip Rake Tine Brush Half Replacement Replacement 1. Remove brush from sweeper. 1. Remove tine retainer and slide damaged tine out. 2. Loosen clamps with a allen wrench and remove from brush halves. Figure 35 1. Clamp Figure 34 1.

  • Page 23: Changing Tires

    Changing Tires Warning 1. Park machine on a flat, level surface. Block other tire to prevent accidental rolling or injury. CALIFORNIA 2. Place jack under frame or axle shaft behind wheel and Proposition 65 Warning jack up wheel until it just contacts floor. Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals Warning...

  • Page 24: The Toro General Commercial Products Warranty

    Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfi ed with your Distributor’s service or have diffi...

Table of Contents