Makita GA5020 Instruction Manual
Angle grinder
Hide thumbs
Also See for GA5020:
- Instruction manual (144 pages) ,
- Parts breakdown (2 pages) ,
- Technical information (9 pages)
Table of Contents
Related Manuals for Makita GA5020
Summary of Contents for Makita GA5020
- Page 1 INSTRUCTION MANUAL Angle Grinder GA5020 GA5020C GA5021 GA5021C GA6020 GA6020C GA6021 GA6021C 008074 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 2: Specifications
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003 END202-6 For Model GA5020 ENG102-2 Symbols For European countries only The following show the symbols used for the equipment. - Page 3 ENG208-4 If the tool is used for other applications, the vibration Vibration values may be different. vibration total value (tri-axial vector sum) determined according to EN60745: Work mode : surface grinding For Model GA6020 Vibration emission (a ) : 9.5 m/s ENG102-2 h,AG For European countries only...
- Page 4 Power tools Makita Corporation responsible create sparks which may ignite the dust or fumes. manufacturer declare that the following Makita Keep children and bystanders away while machine(s): operating a power tool. Distractions can cause Designation of Machine: you to lose control.
-
Page 5: Specific Safety Rules
Personal safety 20. Store idle power tools out of the reach of 10. Stay alert, watch what you are doing and use children and do not allow persons unfamiliar common sense when operating a power tool. with the power tool or these instructions to Do not use a power tool while you are tired or operate the power tool. - Page 6 Do not use accessories which are not 10. Hold power tool insulated gripping specifically designed and recommended by surfaces only, when performing an operation the tool manufacturer. Just because the where the cutting accessory may contact accessory can be attached to your power tool, it hidden wiring or its own cord.
- Page 7 b) Never place your hand near the rotating b) Do not position your body in line with and accessory. Accessory may kickback over your behind the rotating wheel. When the wheel, at hand. the point of operation, is moving away from your c) Do not position your body in the area where body, the possible kickback may propel the spinning wheel and the power tool directly at you.
-
Page 8: Functional Description
19. Make sure the wheel is not contacting the WARNING: workpiece before the switch is turned on. MISUSE or failure to follow the safety rules stated in 20. Before using the tool on an actual workpiece, this instruction manual may cause serious personal let it run for a while. - Page 9 For tool with lock button Additionally, when the load on the tool exceeds • To start the tool, simply pull the switch trigger. Release admissible levels, power to the motor is reduced to the switch trigger to stop. protect the motor from overheating. When the load For continuous operation, pull the switch trigger and returns to admissible levels, the tool will operate as then push in the lock button.
- Page 10 1. Loop handle 2. Hex wrench 3. Bolt 007993 008048 Screw the side grip securely on the position of the tool Installing or removing wheel guard as shown in the figure. CAUTION: Installing loop handle (Accessory) When using depressed center grinding •...
-
Page 11: Operation
1. Screw 1. Lock nut wrench 2. Shaft lock 008344 007996 Loosen the lever on the wheel guard after loosening the To remove the wheel, follow the installation procedure in screw. Mount the wheel guard with the protrusion on the reverse. -
Page 12: Maintenance
Then check the tool while running and electric brake operation when releasing the switch trigger. If MAINTENANCE electric brake is not working well, ask your local Makita service center for repair. (For models GA5020/GA6020) To maintain product SAFETY and RELIABILITY, repairs,... - Page 16 Makita Corporation Anjo, Aichi, Japan 884710E221...