Makita GA5020 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Grinder
  5. GA5020
  6. Instruction manual

Makita GA5020 Instruction Manual

Hide thumbs Also See for GA5020:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
INSTRUCTION MANUAL
Angle Grinder
GA5020
GA6020
008074
DOUBLE INSULATION
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1

Advertisement

Table of Contents
loading

Related Manuals for Makita GA5020

Summary of Contents for Makita GA5020

  • Page 1 INSTRUCTION MANUAL Angle Grinder GA5020 GA6020 008074 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    Safety class • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Note: Specifications may differ from country to country. END202-3 For Model GA5020 ENG102-1 Symbols For European countries only The following show the symbols used for the equipment.

  • Page 3: General Safety Rules

    3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN personal injury. Authorized Representative in Europe: 10. Use safety equipment. Always wear eye Makita International Europe Ltd. protection. Safety equipment such as dust mask, Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 non-skid safety shoes, hard hat, or hearing...

  • Page 4: Specific Safety Rules

    dangerous in the hands of untrained users. The rated speed of the accessory must be at 20. Maintain power tools. Check for misalignment least equal to the maximum speed marked on or binding of moving parts, breakage of parts the power tool. Accessories running faster than and any other condition that may affect the their rated speed can break and fly apart.
  • Page 5 cut or snagged and your hand or arm may be sharp edges etc. Avoid bouncing and snagging pulled into the spinning accessory. the accessory. Corners, sharp edges or bouncing 13. Never lay the power tool down until the have a tendency to snag the rotating accessory accessory has come to a complete stop.
  • Page 6 occur. Investigate and take corrective action to 29. Do not leave the tool running. Operate the tool eliminate the cause of wheel binding only when hand-held. d) Do not restart the cutting operation in the 30. Do not touch the workpiece immediately after workpiece.

  • Page 7: Functional Description

    FUNCTIONAL DESCRIPTION To start the tool, simply pull the switch trigger. Release the switch trigger to stop. CAUTION: For continuous operation, pull the switch trigger and Always be sure that the tool is switched off and • then push in the lock button. unplugged before adjusting or checking function on To stop the tool from the locked position, pull the switch the tool.

  • Page 8: Operation

    Always install the loop handle on the tool before Installing or removing depressed center operation. Hold the tool's switch handle and the loop grinding wheel/Multi-disc (accessory) handle firmly with both hands during operation. Install the loop handle so that its protrusion will fit into WARNING: the matching hole in the gear housing.

  • Page 9: Maintenance

    NEVER use tool with wood cutting blades and kickback, wheel breakage and overheating of the • other sawblades. Such blades when used on a motor may occur. grinder frequently kick and cause loss of control Do not start the cutting operation in the workpiece. •...
  • Page 10 Your failure to do so could result in personal injury to you and others. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Wheel guard (Wheel cover) • Inner flange •...
  • Page 12 Makita Corporation Anjo, Aichi, Japan 884710-221...

This manual is also suitable for:

Ga6020

Table of Contents