Makita DF010D Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Drill
  5. DF010D
  6. Instruction manual
Makita DF010D Instruction Manual

Makita DF010D Instruction Manual

In-line cordless driver drill
Hide thumbs Also See for DF010D:
Table of Contents

Advertisement

Quick Links

See also: Technical Information , Instruction Manual
INSTRUCTION MANUAL
In-line Cordless Driver Drill
DF010D
008706
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1

Advertisement

Table of Contents
loading

Related Manuals for Makita DF010D

Summary of Contents for Makita DF010D

  • Page 1 INSTRUCTION MANUAL In-line Cordless Driver Drill DF010D 008706 WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    EC Declaration of Conformity ENG103-4 Makita Corporation responsible Noise manufacturer declare that the following Makita The typical A-weighted noise level determined according machine(s): to EN60745: Designation of Machine: Sound pressure level (L ) : 70 dB(A) or less...

  • Page 3: General Power Tool Safety Warnings

    Do not abuse the cord. Never use the cord for representative in Europe who is: carrying, pulling or unplugging the power tool. Makita International Europe Ltd, Keep cord away from heat, oil, sharp edges or Michigan, Drive, Tongwell, moving parts. Damaged or entangled cords Milton Keynes, MK15 8JD, England increase the risk of electric shock.
  • Page 4 18. Do not use the power tool if the switch does 29. Follow instruction lubricating not turn it on and off. Any power tool that cannot changing accessories. be controlled with the switch is dangerous and 30. Keep handles dry, clean and free from oil and must be repaired.

  • Page 5: Functional Description

    FUNCTIONAL DESCRIPTION If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns CAUTION: and even an explosion. Always be sure that the tool is switched off and the • If electrolyte gets into your eyes, rinse them battery cartridge is removed before adjusting or out with clear water and seek medical checking function on the tool.

  • Page 6: Switch Action

    Switch action CAUTION: Always set the speed change lever fully to the • 1. Lock button correct position. If you operate the tool with the 2. Switch speed change lever positioned halfway between the "1" side and "2" side, the tool may be damaged.
  • Page 7 Guideline for clutch auto-stop Work range of clutch auto-stop Increments on adjusting Fastening torque ring for fastening torque High speed Low speed Approx. 0.3 N m (Approx. 3 Kgf-cm) Approx. 0.82 N m Clutch auto-stop works (Approx. 8.4 Kgf-cm) Approx. 1.35 N m (Approx.
  • Page 8 (1). position. To turn off the light, slide the lamp switch to B B=14mm (Note) Makita bits are these types. position. Even if you leave the lamp on, the light will automatically To install these types of bits, follow turn off after 5 minutes.

  • Page 9: Screwdriving Operation

    To install the bit, pull the sleeve in the direction of CAUTION: the arrow and insert the bit-piece and bit into the Adjust the adjusting ring to the proper torque level • sleeve as far as it will go. The bit-piece should be for your work.

  • Page 10: Maintenance

    If you need any assistance for more details regarding If the tool is operated continuously until the battery • these accessories, ask your local Makita Service Center. cartridge has discharged, allow the tool to rest for Drill bits •...
  • Page 12 Makita Corporation Anjo, Aichi, Japan 884799B229...

Table of Contents