Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cisco PTZ
Summary of Contents for Cisco PTZ
- Page 1 Cisco Video Surveillance PTZ IP Camera Installation Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-28954-01...
- Page 2 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.
-
Page 3: Table Of Contents
C H A P T E R Understanding the PTZ IP Camera User Interface PTZ IP Camera Window Links PTZ IP Camera Windows Powering the PTZ IP Camera On or Off Resetting the PTZ IP Camera Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01... - Page 4 Contents Viewing Live Video Camera Settings Motion Detection Settings Pan/Tilt/Zoom Settings 4-10 Privacy Zone 4-12 N D E X Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01...
-
Page 5: Preface
Obtaining Documentation, Obtaining Support, and Security Guidelines For information about obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed... - Page 6 Preface Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01...
-
Page 7: Chapter 1 Overview
C H A P T E R Overview This chapter describes the Cisco Video Surveillance pan, tilt, and zoom (PTZ) IP cameras, and includes the following topics: Introduction, page 1-1 • Package Contents, page 1-2 • PTZ IP Camera Physical Details, page 1-3 •... -
Page 8: Package Contents
Chapter 1 Overview Package Contents Package Contents The Cisco Video Surveillance PTZ IP camera package includes the following items: Cisco Video Surveillance PTZ IP Camera (1) • Pendant cap (1) • Screw driver (1) • Ethernet cable (1) • O-RING (1) •... -
Page 9: Ptz Ip Camera Physical Details
PTZ IP Camera Physical Details PTZ IP Camera Physical Details Figure 1-1 and the table that follows describe the outer view of the PTZ IP camera. Figure 1-1 Outer View of the PTZ IP Camera This drawing shows a camera with its dome cover removed. -
Page 10: Status Leds
Board to board connector. SD/SDHC/SDXC Card Slot Slot for the SD, SDHC, or SDXC card. Status LEDs Table 1-1 describes the LED indicator for each PTZ IP camera status state. Table 1-1 Status LEDs Status Green Camera is done booting and is available for use. - Page 11 RJ45 Plug General I/O Terminal Block Ethernet 10/100 RJ45 Plug Plug for a standard LAN cable to connect the PTZ IP camera to a 10/100BaseT router or switch. General I/O Terminal Block General purpose input/output (GPIO) terminal block that is used to connect external input and output devices.
- Page 12 Chapter 1 Overview PTZ IP Camera Physical Details Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01...
-
Page 13: Chapter 2 Installing The Camera
To power the PTZ IP camera with Power over Ethernet (PoE), a switch must be 802.3af compliant. If you are using the PTZ IP camera on a network connection that does not provide PoE, you must • use a third-party AC 24V power adapter. -
Page 14: Warnings Before Installation
Chapter 2 Installing the Camera Warnings Before Installation Warnings Before Installation Power off the PTZ IP camera as soon as Do not manually pan and tilt the PTZ IP • • smoke or unusual odors are detected. camera when the power is on. -
Page 15: Installing The Ptz Ip Camera
This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353 Inline power circuits provide current through the communication cable. Use the Cisco provided cable or Caution a minimum 24AWG communication cable. -
Page 16: Cabling Through Waterproof Connectors
The recommended cable gauge is 1.2–1.8 mm. There are 16 holes on the seal (B), and the widest holes with a crack on the side are specific Note for power cables. Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01... -
Page 17: Connecting The Cables
Strip about 1/2 inch (12 mm) of the sheath from the Ethernet cable. Step 3 Use an RJ45 crimping tool to attach the Ethernet wires to a connector. When done, connect the cable to Step 4 the camera’s Ethernet RJ45 socket. Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01... -
Page 18: Preparing The Camera
Remove the black dome cover of the camera. Step 2 Turn the camera upside down. Step 3 Attach the silica gel packets to the inside wall of the camera using the adhesive strips. Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01... -
Page 19: Mounting To The Wall
Installing the PTZ IP Camera Attach the black cover to the camera. Step 4 Mounting to the Wall You can connect the PTZ IP camera to the wall using the following accessories: Goose neck for wall mount—CIVS-6KA-GNECK= • Adaptor—CIVS-PA-PTZADPTR= •... -
Page 20: Mounting The Ptz Camera
Rotate the camera clockwise until its alignment mark is aligned with the "C" mark. Step 5 Use the included T25 stardriver to securely tighten the three anti-tamper screws from the top. Step 6 Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01... -
Page 21: Mounting To The Ceiling
Installing the Camera Installing the PTZ IP Camera Alignment Mark C Mark Mounting to the Ceiling You can connect the PTZ IP camera to the ceiling using the following accessories: 20cm Pendent Pipe with Adaptor Installed—CIVS-PA-EXT= • Pendant Head—CIVS-6KA-PENHEAD= •... - Page 22 Route power lines and other wires through the pendant head. You may apply a 1 inch conduit. Step 4 Secure the pendant head to the ceiling by using the M6.2 x75mm screws. Step 5 Cisco Video Surveillance PTZ IP Camera Installation Guide 2-10 OL-28954-01...
- Page 23 Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. Attach the camera using Step 4–Step 6 in the Mounting the PTZ Camera section. Step 7 Cisco Video Surveillance PTZ IP Camera Installation Guide 2-11 OL-28954-01...
-
Page 24: Connecting To The Network
IP Camera” section on page 3-1 to access the camera through your network. After completing the initial setup, use the PTZ IP camera user interface in the Managing the Camera • section to adjust the focal length and zoom factor. -
Page 25: Chapter 3 Performing The Initial Setup Of The Ip Camera
HTTP connection in addition to the default HTTPS (HTTP secure) connection. To make these configuration settings, you connect to the PTZ IP camera from any PC that is on the same network as the PTZ IP camera. The PC must meet these requirements: •... - Page 26 Chapter 3 Performing the Initial Setup of the IP Camera In the Password and Confirm Password fields of the admin row, enter a password for the PTZ IP camera Step 3 administrator. You must enter the same password in both fields. The password is case sensitive and must contain at least eight characters, which can be letters, numbers, and special characters, but no spaces.
-
Page 27: Chapter 4 Managing The Camera
• Understanding the PTZ IP Camera User Interface After you log in to the PTZ IP camera, you can access the windows and perform a variety of administrative and user procedures. The links and activities that you can see and access in the PTZ IP camera windows depend on your camera privilege level. -
Page 28: Ptz Ip Camera Windows
Method by which the PTZ IP camera obtains its IP address. LAN IP IP address of the LAN to which the PTZ IP camera is connected. Subnet Mask Subnet mask of the LAN to which the PTZ IP camera is connected. -
Page 29: Powering The Ptz Ip Camera On Or Off
Powering the PTZ IP Camera On or Off The PTZ IP camera does not include an on/off switch. You power it on or off by connecting it to or disconnecting it from a power source. When you power off the PTZ IP camera, configuration settings are retained. -
Page 30: Viewing Live Video
To view live video, log in to the PTZ IP camera, then click View Video in the PTZ IP camera Main window menu bar. The Camera Video & Control window appears. This window displays live video from the camera and lets you control a variety of camera and display functions. - Page 31 Displays the default video image, which is not rotated and not reversed. Full Screen button Displays the video image in full screen mode. To return to normal display mode, click the full screen image. Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01...
-
Page 32: Camera Settings
Values are 1 through 10. A higher value increases the brightness and a lower value decreases the brightness. For example, if the PTZ IP camera is facing a bright light and the video appears too dark, you can increase the brightness. - Page 33 Camera Settings (continued) Control Description Sharpness slider To control the sharpness of the video from the PTZ IP camera, drag the slider. Values are 1 through 100. A higher value increases the sharpness and a lower value decreases the sharpness.
- Page 34 For extremely light and dark areas, enable the wide dynamic range (WDR) feature to ensure you can clearly view the objects in the scene. Options are • Off (default) Auto • Manual • Cisco Video Surveillance PTZ IP Camera Installation Guide OL-28954-01...
-
Page 35: Motion Detection Settings
When motion detection is enabled, the PTZ IP camera monitors activity in regions of the video that you specify. If activity at a defined level occurs in any of these areas, the PTZ IP camera generates an alert and takes the actions that are configured as described in the “Event Notification Window”... -
Page 36: Pan/Tilt/Zoom Settings
Enable Digital Zoom Check this box to enable digital zoom. Enable Auto Focus Check this box to automatically focus the PTZ IP camera for the selected zoom. Focus To manually control the field of view focus, use the left arrow to focus on near objects. - Page 37 Auto Pan/Patrol Speed—Use the slider to set the rate at which the camera automatically pans and patrols based on the patrol list. Values are 1 through 100. Default is 50. Cisco Video Surveillance PTZ IP Camera Installation Guide 4-11 OL-28954-01...
-
Page 38: Privacy Zone
Privacy Zone The controls in Table 4-8 appear when you click the Up Arrow in the Privacy Zone area at the bottom of the video image. Cisco Video Surveillance PTZ IP Camera Installation Guide 4-12 OL-28954-01... - Page 39 To focus on a particular Privacy Zone, select the region name from Privacy Mask drop down list. The camera automatically pans and tilts to the masked region. Cisco Video Surveillance PTZ IP Camera Installation Guide 4-13 OL-28954-01...
- Page 40 Chapter 4 Managing the Camera Viewing Live Video Cisco Video Surveillance PTZ IP Camera Installation Guide 4-14 OL-28954-01...
-
Page 41: I N D E X
DHCP, obtaining IP address through live video viewing factory reset through home window through third-party device or software See also video log out, of IP camera help, for IP camera windows Cisco Video Surveillance PTZ IP Camera Installation Guide IN-1 OL-28954-01... - Page 42 Power over Ethernet (PoE) rebooting, IP camera Refresh link reset factory default values reboot Setup window description displaying sharpness video viewing live through Home window through third-party device or software Cisco Video Surveillance PTZ IP Camera Installation Guide IN-2 OL-28954-01...