Advertisement
Quick Links
Remove and Replace Cisco NCS 1014 Modules
This chapter describes the procedures to replace Cisco NCS 1014 modules.
Caution
All the modular slots in the NCS 1014 chassis should always be populated with respective modules (line-cards,
controller, PSU & fan units). Empty line card slots to be populated with filler modules, which are shipped
with the chassis. The replacement or upgrade of the modules (Online Insertion or Removal, OIR) to be
performed only when the ambient temperature is below 30-degree C. The OIR of modules should be completed
within five minutes to prevent overheating of the components.
•
•
Remove and Replace a Line Card, on page 2
•
•
Remove and Replace the Controller, on page 5
•
Remove and Replace the Fan Module, on page 6
•
•
Wipe Data in Disk Using Secure Erase, on page 10
Remove and Replace the Pluggables in the 2.4T Line Card
Use this procedure to remove and replace the pluggables in the 2.4T DWDM line card.
Note
This procedure is applicable to replacing pluggables in other line cards too.
Remove and Replace Cisco NCS 1014 Modules
1
Advertisement
Related Manuals for Cisco NCS 1014
Summary of Contents for Cisco NCS 1014
-
Page 1: Table Of Contents
This chapter describes the procedures to replace Cisco NCS 1014 modules. Caution All the modular slots in the NCS 1014 chassis should always be populated with respective modules (line-cards, controller, PSU & fan units). Empty line card slots to be populated with filler modules, which are shipped with the chassis. -
Page 2: Remove And Replace A Line Card
Install the Pluggables Remove and Replace a Line Card Use this procedure to remove and replace the line card or filler card in the Cisco NCS 1014 chassis. Caution Perform the removal and replacement procedure for a line card or filler card only when the ambient temperature is below 30℃... - Page 3 Remove and Replace Cisco NCS 1014 Modules Remove and Replace the Power Supply Unit (PSU) • Remove the cable retainers and the power cables, in case of an AC power supply unit. • Remove the protection covers, fasteners, and lugs, in case of a DC power supply unit.
- Page 4 Remove and Replace Cisco NCS 1014 Modules Remove and Replace the Power Supply Unit (PSU) Figure 2: Locking Latch on the AC PSU Locking latch Step 2 Holding the handle with one hand and supporting the PSU with the other, gently pull out the PSU from the slot.
-
Page 5: Remove And Replace The Controller
Install the Power Supply Units (PSUs). Remove and Replace the Controller Use this procedure to remove and replace the controller in the Cisco NCS 1014 chassis. Step 1 Using a T15 six lobe/slot screwdriver, unfasten the two screws on the controller. -
Page 6: Remove And Replace The Fan Module
Figure 4: Removing the Controller Controller Card What to do next Install Controller Remove and Replace the Fan Module Use this procedure to remove and replace a fan module in the Cisco NCS 1014 chassis. Remove and Replace Cisco NCS 1014 Modules... - Page 7 Remove and Replace Cisco NCS 1014 Modules Remove and Replace the Fan Module Caution Online insertion and removal (OIR) duration for the fan module at 30℃ ambient temperature is five minutes. Step 1 Push and hold the spring-loaded lever toward the left with your thumb (unlock position).
-
Page 8: Remove And Replace The Solid State Drive (Ssd)
Module. Remove and Replace the Solid State Drive (SSD) Use this procedure to remove and replace the SSD in the Cisco NCS 1014 chassis. Step 1 Using a T15 six lobe/slot screwdriver, loosen the lone captive screw on the SSD. - Page 9 Remove and Replace Cisco NCS 1014 Modules Remove and Replace the Solid State Drive (SSD) Figure 7: Removing the SSD Callout Component Captive screw Step 2 Remove the SSD. To remove, gently pull out the SSD from the slot. What to do next...
-
Page 10: Wipe Data In Disk Using Secure Erase
Warning Use this procedure only during RMA. Before you begin Take out the NCS 1014 unit that you planned for RMA out of the data center and the network. Access NCS 1014 only using the console port. Step 1 When NCS 1014 boots (power cycle), the following message appears.