Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell ELSTON
Summary of Contents for Honeywell ELSTON
- Page 1 ELSTON 52” CEILING FAN MODEL #10290 Español p. 21 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, ensure Care and Maintenance ......2 that all parts are present. -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blade (5) 2. Mounting Bracket 3. Canopy 4. Canopy Cover 5. Yoke Cover 6. Downrod 7. Downrod Pin 8. Downrod Clip 9. Blade Arm (5) 10. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS 1. Your fan has 3 mounting options: Fig. 1 • Standard (Fig. 1) • Angle (Fig. 2) • Closemount (Fig. 3) Note: The fans in figures 1 through 3 are not the actual fan in your package, they are representation of the 3 different mounting options. -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 4. Turn off the circuit breakers and wall switch leading Fig. 4 to the fan wire leads (Fig. 4). WARNING Failure to disconnect the power supply prior to installation may result in serious injury or death. 5. Loosen all four preassembled mounting bracket Fig. -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 7. Partially loosen the set screws in the yoke at the Fig. 7 top of the motor assembly (Fig. 7). Set Screws Fig. 8 8. Remove the downrod clip and downrod pin from the downrod (Fig. 8). Downrod Clip Downrod Pin... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 10. Slide the downrod into the yoke of the motor Fig. 10 assembly, align the holes, and reinstall the downrod pin and downrod clip. Then secure with set screws (Fig. 10). Downrod Downrod Downrod Clip Yoke 11.
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 13. Install the ball end of the downrod into the Fig. 13 mounting bracket opening. Align the slot in the ball with the tab in the mounting bracket. The downrod should not rotate if installed correctly (Fig. 13). Slot Mounting WARNING...
-
Page 10: Closemount Instructions
CLOSEMOUNT INSTRUCTIONS 14. Remove the canopy cover from the bottom of the Fig. 14 canopy (Fig. 14). Helpful Hint: The downrod, yoke cover and canopy cover are not used in this type of installation. Canopy Cover Canopy 15. Align the canopy with the holes in the top of motor Fig. -
Page 11: Wiring
WIRING CAUTION Fig. 17 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (Hot) WARNING If house wires are different colors than referred to in White (Neutral) the following steps, consult a professional electrician Bare/Green (Ground) to determine wiring. -
Page 12: Canopy Installation
CANOPY INSTALLATION 19. Lift the canopy up so the partially installed mounting Fig. 19 bracket screws are engaged in the J-slots on each side of the canopy. Rotate the canopy clockwise and install the previously removed mounting bracket screws from Step 5 (Fig. 19). Tighten all the mounting bracket screws. -
Page 13: Blade Installation
BLADE INSTALLATION 20. Remove motor screws, motor blocks and washers Fig. 19 Fig. 20 from underside of the motor assembly. Discard the motor blocks and washers but keep the motor screws for blade arm attachment. (Fig. 20). Motor Block Motor Screw Washer Motor Screw Motor Block... -
Page 14: Light Kit Installation
LIGHT KIT INSTALLATION 23. To install the fan with the LED light kit: Fig. 23 Remove the three fitter plate screws from fitter plate. Then connect the 9-pin connector from the Fitter Plate motor assembly to the 9-pin connector from the LED light kit. - Page 15 LIGHT KIT INSTALLATION 26. Feed the fan pull chain from the switch housing Fig. 26 through chain guide and the grommet in the light kit and then through the off-center hole in the glass Chain Guide bowl. Then, feed the pull chain from the light kit Switch Housing through the center hole in the glass bowl, rubber Grommet...
- Page 16 LIGHT KIT INSTALLATION 28. (Optional) To install the fan without the light kit: Hex Nut Fig. 28 Washer Unscrew the hex nut and washer from the threaded rod in the switch housing to remove the LED light kit and wiring (Fig. 28). Switch Housing LED Light Kit...
-
Page 17: Operating Instructions
OPERATING INSTRUCTIONS 31. Using a ceiling fan will allow you to raise your Fig. 31 thermostat in the summer and lower your thermostat in the winter without sacrificing comfort (Fig. 31). Important: Wait for the fan to stop before moving the reverse switch. -
Page 18: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 10290 PIECE DESCRIPTION PART # Blade Arm 10290-A Blade 10290-B Glass Bowl 10290-C Hardware bag (not shown) -
Page 19: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection. -
Page 20: Limited Lifetime Warranty
1-877-361-3883 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.