Makita UT001G Instruction Manual page 11

Operation of speed adjusting dial
The tool speed can be adjusted steplessly by turning
the speed adjusting dial. The no load speed when the
switch trigger is fully pulled can be adjusted 270 min
-1
to 500 min at low speed mode, 500 min
at high speed mode. Higher speed is obtained when the
dial is turned in the direction of number 5; lower speed is
obtained when it is turned in the direction of number 1.
Select the proper speed for the material to be mixed.
► Fig.17: 1. Speed adjusting dial
NOTICE:
The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1.
Accidental restart preventive function
If you install the battery cartridge while pulling the
switch trigger or locking the switch trigger, the tool does
not start. To start the tool, release the switch trigger, and
then pull the switch trigger.
Electronic function
The tool is equipped with the following electronic func-
tion for easy operation.
Soft start
The soft-start function minimizes start-up shock, and
makes the tool start smoothly.
Basic operations
CAUTION:
Do not mix flammable materials or
operate the tool around flammable materials such
as paint with thinner used as solvent. Failure to do
so may cause an injury.
CAUTION:
Do not mix high viscosity material
in the high speed mode. You may lose the control of
the tool and cause an injury.
CAUTION:
Do not rotate the mixing blade
outside the stirring vessel.
CAUTION:
If you hear an abnormal noise during
use, turn off the switch and stop using the tool.
NOTICE:
When you mix the material while the
mixing blade floating out of the material, be care-
ful not to splash the material.
NOTICE:
Do not use the tool for any purpose
other than stirring mortar, concrete, etc.
1. Select high speed mode or low speed mode
according to the material to be mixed.
2. Hold the tool firmly with both hands. Place the mix-
ing blade under material fully. Check that the material is
not solidified and the safety of the work site, then turn
on the tool.
3. Move the mixing blade up and down during the mix-
ing operation so that whole part of material can be mixed.
4. When finishing mixing, turn off the tool. Make sure
that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.
Applied operations
switched off and the battery cartridge is removed
-1
before adjusting or checking function on the tool.
-1 -1
to 920 min
Replacing battery cover
Optional accessory
Install one of the battery covers to fit the size of your
battery cartridge.
► Fig.18: 1. Battery cover S 2. Battery cover L
1.
pressing the button on the battery cover.
2.
battery cover. Then remove the screw, sleeve and the
battery cover.
► Fig.19: 1. Screw 2. Sleeve 3. Battery cover (stan-
NOTE: The sleeve may remain in the mounting holes.
In that case, pull it out using a screw or the like.
3.
cover with the mounting holes on the housing. Insert the
sleeve. Then tighten the screws to secure it in place.
► Fig.20: 1. Screw 2. Sleeve 3. Battery cover
4.
Installing or removing the shaft
holder
country specific
For UT001G
Install one of the shaft holders optionally available to fit
your screw size of the shaft.
► Fig.21: 1. M12 shaft holder 2. M14 shaft holder
While holding the spindle with a wrench, loosen the
shaft holder with another wrench.
► Fig.22: 1. Shaft holder 2. Wrench 3. Spindle
To install the shaft holder, perform the removal proce-
dure in reverse.
For UT002G
1.
loosen the chuck with the hex wrench while holding the
spindle with the wrench.
► Fig.23: 1. Hex wrench 2. Chuck 3. Wrench
2.
ing the spindle with another wrench.
► Fig.24: 1. Shaft holder 2. Wrench 3. Spindle
11 ENGLISH
CAUTION:
Always be sure that the tool is
3. Button
Open the standard equipped battery cover while
Loosen the screw securing the standard equipped
dard equipped)
Align the mounting hole on the optional battery
(optional)
Close the battery cover securely.
Insert the hex wrench into the chuck, and then
4. Spindle
Tighten the shaft holder with a wrench while hold-