Applied Operations; Maintenance; Troubleshooting; Optional Accessories - Makita UT001G Instruction Manual

3. Move the mixing blade up and down during the
mixing operation so that whole part of material can be
mixed.
4.
When finishing mixing, turn off the tool. Make sure
that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.

Applied operations

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Replacing battery cover
Optional accessory
Install one of the battery covers to fit the size of your
battery cartridge.
► Fig.18: 1. Battery cover S 2. Battery cover L
3. Button
1. Open the standard equipped battery cover while
pressing the button on the battery cover.
2. Loosen the screw securing the standard equipped
battery cover. Then remove the screw, sleeve and the
battery cover.
► Fig.19: 1. Screw 2. Sleeve 3. Battery cover (stan-
dard equipped)
NOTE: The sleeve may remain in the mounting holes.
In that case, pull it out using a screw or the like.
3.
Align the mounting hole on the optional battery
cover with the mounting holes on the housing. Insert the
sleeve. Then tighten the screws to secure it in place.
► Fig.20: 1. Screw 2. Sleeve 3. Battery cover
(optional)
4. Close the battery cover securely.
Installing or removing the shaft
holder
country specific
For UT001G
Install one of the shaft holders optionally available to fit
your screw size of the shaft.
► Fig.21: 1. M12 shaft holder 2. M14 shaft holder
While holding the spindle with a wrench, loosen the
shaft holder with another wrench.
► Fig.22: 1. Shaft holder 2. Wrench 3. Spindle
To install the shaft holder, perform the removal proce-
dure in reverse.
For UT002G
1. Insert the hex wrench into the chuck, and then
loosen the chuck with the hex wrench while holding the
spindle with the wrench.
► Fig.23: 1. Hex wrench 2. Chuck 3. Wrench
4. Spindle
2. Tighten the shaft holder with a wrench while hold-
ing the spindle with another wrench.
► Fig.24: 1. Shaft holder 2. Wrench 3. Spindle
Handling after use
Use a wet cloth or the like to carefully wipe off the mate-
rial left on the tool after use. Extra care should be given
to thorough cleaning of the vents, switch area, cover
openings, etc.
NOTICE:
Avoid cleaning the tool in water. Water
will get into the motor housing and cause motor
failure.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.

Troubleshooting

Before asking for repairs, check the following points.
1. Turn the tool off, and then turn it on again to
restart.
2. Charge the battery(ies) or replace it/them with
recharged battery(ies).
3. Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Mixing blade
• Shaft
• Battery cover
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
13 ENGLISH