Maintenance; Operation - Makita CL107FDZW Instruction Manual

3. There is no distinction between the upper and
lower sides of the paper filter. You may insert its pro-
trusion of any side into the lower groove of the dust
stopper.
► Fig.21: 1. Lower groove
4.
Overlap the frame of dust stopper with that of the
paper filter.
► Fig.22
5. Place the dust stopper and the paper filter
together into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way into
the slots in the cleaner cavity.
► Fig.23
6. Place the entire container part of the paper filter
inside the tool itself.
► Fig.24
7. Close the front cover completely.

OPERATION

To connect attachments, such as nozzle, twist and
insert the attachment securely. To disconnect the
attachments, twist and extract it.
► Fig.25
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
► Fig.26: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
► Fig.27: 1. Cleaner body 2. Extension wand
3. Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
► Fig.28: 1. Corner nozzle 2. Cleaner body
Corner nozzle +Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
► Fig.29: 1. Corner nozzle 2. Extension wand
3. Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
► Fig.30

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks may result.
After use
NOTICE:
Putting the cleaner against the wall
without any other support cause the cleaner to
fall down and be damaged.
► Fig.31
Cleaning
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/paper filter
mounting area and the dust stopper.
► Fig.32
Wash the filter in soapy water when it is clogged with dust
and the cleaner power becomes weak. Dry it out thor-
oughly before use. An insufficiently dried filter may cause
poor suction and shorten the service life of the motor.
► Fig.33
NOTE: Paper filter is a throw-away type.
When the sponge filter is clogged with dust, remove it
from the cleaner and then wipe it off or wash in water.
Removing and installing the sponge filter
CAUTION:
After cleaning sponge filter, be
sure to install it on the cleaner. If washed in water,
dry it up before installing. An insufficiently dried
sponge filter may shorten the service life of the motor.
To remove the sponge filter, remove the dust bag or
paper filter and then pinch and take it out.
► Fig.34: 1. Sponge filter
Press in the whole edge of the sponge filter against the
recessed wall inside the dust bag/paper filter mounting area.
► Fig.35: 1. Recessed wall
Wall mount for cordless cleaner
Optional accessory
NOTE: The screw to mount the holder is not included.
Prepare a screw which fits with the material to screw into.
Attach the wall mount for cordless cleaner to a hard wooden wall,
beam or column, where the wall mount for cordless cleaner can
be firmly secured. Always be sure that the wall mount for cordless
cleaner is securely attached before hanging the cleaner.
► Fig.36: 1. Wall mount for cordless cleaner
CAUTION:
Do not hang the cleaner to the wall
mount violently or hang other appliances than the
cleaner.
11 ENGLISH