Functional Description - Makita DVC860L Instruction Manual

5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery burst-
ing causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
Charge the battery cartridge before completely
1.
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery car-
tridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tem-
perature at 10°C - 40°C (50°F - 104°F). Let a hot
battery cartridge cool down before charging it.
Charge the battery cartridge if you do not use
4.
it for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
Use with AC power:
WARNING:
Before plugging the cleaner, always make
•
sure that the cleaner is switched off. Plugging
the cleaner with the switch on may cause an
unexpected start resulting in serious personal
injury.
► Fig.1: 1. Plug (the shape and cord length may differ
from country to country)
Connect the plug to a power supply.
► Fig.2: 1. AC power indicator
The AC power indicator lights up when setting the
stand-by switch to "I" side.
NOTE:
• Even operating in DC power mode , the tool
is automatically changed into AC power mode
when plugged in.
• If the tool is unplugged during operation with the
battery inserted, the cleaner gets into stand-by
state.
Use with battery:
Installing or removing battery
cartridge
CAUTION:
• Always be sure that the cleaner is switched off,
unplugged, and the battery cartridge is removed
before adjusting or checking function on the
tool.
• Hold the cleaner and the battery cartridge
firmly when installing or removing battery
cartridge. Failure to hold the cleaner and the
battery cartridge firmly may cause them to slip
off your hands and result in damage to the
cleaner and battery cartridge and a personal
injury.
• Be careful not to pinch your fingers when
opening or closing the battery cover. Failure
to do so may cause personal injury.
► Fig.3: 1. Lock 2. Battery cover
To install the battery cartridge, release the lock first,
and open the battery cover. And then, insert the battery
cartridge.
► Fig.4: 1. Battery cartridge
Align the tongue on the battery cartridge with the groove
in the housing and slip it into place. Insert it all the way
until it locks in place with a little click. Then lock the
battery cover.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
9 ENGLISH