Makita VC2012L Service Manual
Hide thumbs
Also See for VC2012L:
- Original operating instructions (137 pages) ,
- Operating instructions manual (16 pages)
Advertisement
Advertisement
Related Manuals for Makita VC2012L
Summary of Contents for Makita VC2012L
- Page 1 VC2012L VC2512L VC3011L SERVICE MANUAL...
-
Page 2: Table Of Contents
CONTENTS 1. EXCHANGE OF COVER….……………………..3 2. EXCHANGE OF CLAMPING PLATE PART....4 3. EXCHANGE OF SOCKET PART…......5 4. EXCHANGE OF MOTOR PART………………..6 5. EXCHANGE OF FILTER ELEMENT………....7 6. EXCHANGE OF DEDUSTING FLAP……....8 7. EXCHANGE OF CASTOR WHEELS……………..8 8. ACTUAL WIRING DIAGRAM……………….....10... -
Page 3: Exchange Of Cover
1. EXCHANGE OF COVER Insert the tip of flathead screwdriver into the When removing Filter cleaning, insert the tip of flathead gap between Handle and Cover. Then, screwdriver into the gap, and pry it off slowly. remove the upper part of Handle. HANDLE BLACK DEDUSTING KNOB BLACK... -
Page 4: Exchange Of Clamping Plate Part
2. EXCHANGE OF CLAMPING PLATE PART Remove two Screws located at the Cable outlet, and then remove the Cable. CABLE OUTLET SCREW 5X18 TX20 When assembling the Cable, make sure to bend it (as shown in the picture) to surely fit it inside. CLAMPING PLATE... -
Page 5: Exchange Of Socket Part
3. EXCHANGE OF SOCKET PART Remove two Screws located at the inner side of Socket cover. Next, remove the Screws that are fixing the wires at the back side. Then, exchange Socket. SOCKET SCREW 3,5X18 TX10 If you remove the two Screws (located at the inner side of Socket) before removing the Socket Cover, the PLUG SOCKET FIXING PLATE (at the back side) will come off as shown in the picture below. -
Page 6: Exchange Of Motor Part
4. EXCHANGE OF MOTOR PART Remove six Screws of Clamping plate. Then, remove the Clamping plate. SCREW 5X18 When removing Clamping plate, since it’s connected with TX20 Motor through wires, make sure to support the Motor with your hands. Be careful not to drop the Motor or disconnect the wires. -
Page 7: Exchange Of Filter Element
If you put Motor on Base plate when assembling the Motor, the position of Upper and Lower Sealings will be shifted, and the Sealings will be pinched between the parts. Therefore, make sure to put the Motor on Clamping plate side, and then attach the Base plate from above. *Note: When putting Motor on Clamping plate, make sure that the terminal part of Motor comes close to the holes (refer to the frame in the picture) for passing the wires. -
Page 8: Exchange Of Dedusting Flap
6. EXCHANGE OF DEDUSTING FLAP TORSION SPRING BASE PLATE WITH AIR OUTLET DEDUSTING FLAP TORSION SPRING DEDUSTING Remove Dedusting flap by removing the Torsion spring as FLAP shown in the picture. 7. EXCHGANGE OF CASTER WHEELS 1R263 CONTAINER CASTOR WHEELS CONTAINER Use 1R263 and pry the Caster off 1R263... - Page 9 1. Apply *grease to the metal stem. 2. Put 1R275 in the groove of the plastic portion of new Caster. 3. Hit 1R275 with a plastic hammer. *You can use any kind of grease such as Makita grease N No.2.
-
Page 10: Actual Wiring Diagram
8. ACTUAL WIRING DIAGRAM Connected to Switch 5 Gray Blue White Black Connected to Switch 3 Connected to Switch 2 Connected to Socket 1 Connected to Circuit Board J8 White Connected to Power supply cord Light blue Connected to Switch 4 through Condenser Black Connected to Circuit Board J6 Gray... - Page 11 Power supply cord Black Green (Grounding wire) Blue Connected to Switch 6 Connected to Circuit Board J11 VC2512L Regarding VC2512L, grounding wires separate from Socket. However, regarding VC2012L/3012L, grounding wires separate in the middle of Power supply cord and Socket. VC2012L/VC3011L...