Makita DSP600 Instruction Manual page 7

Cordless plunge cut saw
Hide thumbs Also See for DSP600:
Table of Contents

Advertisement

6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7.
8.
Be careful not to drop or strike battery.
Do not use a damaged battery.
10.
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
aging and labeling must be observed.
For preparation of the item being shipped, consult-
Please also observe possibly more detailed
national regulations.
battery in such a manner that it cannot move
around in the packaging.
11.
Follow your local regulations relating to dis-
posal of battery.
12. Use the batteries only with the products
sive heat, explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2.
3.
Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
Important safety instructions for
wireless unit
1.
Do not disassemble or tamper with the wire-
less unit.
2.
Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
3.
Use the wireless unit only with Makita tools.
4.
Do not expose the wireless unit to rain or wet
conditions.
Installing the batteries to
-
5.
Do not use the wireless unit in places where
the temperature exceeds 50°C (122°F).
6.
Do not operate the wireless unit in places
where medical instruments, such as heart
pace makers are near by.
7.
Do not operate the wireless unit in places
ated, automated devices may develop malfunction
or error.
8.
The wireless unit can produce electromagnetic
user.
-
The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
10.
unit with bare hands or metallic materials.
11.
installing the wireless unit.
12.
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
13. Always insert the wireless unit in the correct
direction.
14.
on the wireless unit too hard and/or press the
-
15. Always close the lid of the slot when
operating.
16.
while the power is being supplied to the tool.
Doing so may cause a malfunction of the wireless
unit.
17.
18. Do not put any sticker on the wireless unit.
static electricity or electrical noise could be
generated.
20.
sun.
21.
could be generated.
22. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
23. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
24. When storing the wireless unit, keep it in the
supplied case or a static-free container.
25.
wireless unit into the slot on the tool.
26. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
27. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
28. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
7 ENGLISH
If oper-
-

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dsp601

Table of Contents