Cisco 10000 SIP-600 Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 10000 SIP-600
  6. Installation manual
Cisco 10000 SIP-600 Installation Manual

Cisco 10000 SIP-600 Installation Manual

10000 series router sip and spa hardware
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco 10000 Series Router SIP and SPA
Hardware Installation Guide
Software Release 12.2(34)SB
August 2008
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-13838-02

Advertisement

Table of Contents
loading

Related Manuals for Cisco 10000 SIP-600

Summary of Contents for Cisco 10000 SIP-600

  • Page 1 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide Software Release 12.2(34)SB August 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-13838-02...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...

  • Page 3: Table Of Contents

    C H A P T E R Bandwidth Oversubscription 3-13 SIP Ingress Oversubscription 3-15 PRE4 Egress Oversubscription 3-15 SIP Performance with a PRE3 3-15 1-Port 10-Gigabit Ethernet SPA Overview 3-16 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...
  • Page 4 5-49 Removing a SIP 5-52 Installing and Removing a SPA 6-57 C H A P T E R Handling SPAs 6-57 Online Insertion and Removal of a SPA 6-58 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...
  • Page 5 C H A P T E R Troubleshooting 7-63 Using debug Commands 7-64 Packing a SPA for Shipment 7-65 Packing a SIP for Shipment 7-65 N D E X Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...
  • Page 6 Contents Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...

  • Page 7: About This Guide

    This document describes the SPA interface processor (SIP) and shared port adapters (SPAs) that are supported on the Cisco 10000 series router. This document also describes how to install the supported SIP and SPAs and how to troubleshoot the installation.

  • Page 8: Document Revision History

    SIP on a Cisco 10000 series router. Chapter 6 Installing and Removing a SPA Describes the procedures for installing and removing a SPA on a Cisco 10000 series router. It also describes how to verify the SIP and SPA installation. Chapter 7...

  • Page 9: Related Documentation 1-Ix

    IOS software document for a particular feature. – To see if a feature is supported by a Cisco IOS release, to locate the software document for that feature, or to check the minimum Cisco IOS software requirements with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com.
  • Page 10 About This Guide Obtaining Documentation, Obtaining Support, and Security Guidelines Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...

  • Page 11: Chapter 1 Sip And Spa Product Overview

    • Power Management, page 1-4 • For software configuration information for the SIPs and SPAs that are supported on the Cisco 10000 series router, refer to the Cisco 10000 Series Router SIP and SPA Software Configuration Guide. Introduction to SIPs and SPAs SIP and SPA carrier card and port adapter architecture increases modularity, flexibility, and density across Cisco Systems routers for network connectivity.

  • Page 12: Shared Port Adapters

    SIP. The SIP also supports OIR with SPAs inserted in their subslots. SIP and SPA Compatibility Table 1-1 shows the SPAs that are supported on the Cisco 10000 series router and the SIPs that support them. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide...

  • Page 13: Modular Optics Compatibility

    Note optics modules with speeds equal to or greater than 10 Gb/s. Cisco Systems qualifies the SFP modules that can be used with SPAs. Note The SPAs accept only the optics modules listed as supported in this document. Each time an SFP or XFP module is inserted into a SPA, a check is run.

  • Page 14: Power Management

    1. Maximum with four SPAs installed Note There are no power consumption restrictions on the types of SPAs inserted in a Cisco 10000 SIP-600, or on the number of SIPs installed in a chassis (up to the maximum of 4 SIPs).

  • Page 15: Sip Summary

    You can check the minimum software requirements of Cisco IOS software with the hardware installed on your router. Use the Software Advisor tool on Cisco.com. This tool does not verify if SIPs or SPAs within a system are compatible, but it provides the minimum Cisco IOS requirements for individual hardware modules or components.

  • Page 16: Identifying Slots And Subslots For Sips And Spas

    Identifying Slots and Subslots for SIPs and SPAs Identifying Slots and Subslots for SIPs and SPAs This section describes how to specify the physical locations of a SIP and SPA on the Cisco 10000 series router using the command-line interface (CLI) to configure or monitor those devices.
  • Page 17 The Transceiver in slot 1 subslot 0 port 2 is ENABLED. The Transceiver in slot 1 subslot 0 port 3 is ENABLED. The Transceiver in slot 1 subslot 0 port 4 is ENABLED. SPA Information: subslot 1/1 SPA-5X1GE-V2 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...
  • Page 18 Card detected 01:25:03 ago Card uptime 0 days, 1 hours, 25 minutes, 3 seconds Card idle time 0 days, 0 hours, 1 minutes, 52 seconds Voltage status: EEPROM contents, slot 5/0: Cisco 10000 Series Router SIP and SPA Hardware Installation Guide OL-13838-02...

  • Page 19: Specifying The Location For A Spa

    2-2. The number for each SPA subslot is indicated by a small numeric label on the SIP faceplate. SPAs in the Cisco 10000 series router use an addressing format that specifies the physical location of the SIP, SPA, and interface in the format slot/subslot/port, where:...

  • Page 20: Cisco 10000 Sip-600 Overview

    SPA. To display information about a SPA, use the show diag, show hw-module sublsot, and show inventory commands. For more information about SPA commands, refer to the Cisco 10000 Series Router SIP and SPA Software Configuration Guide.
  • Page 21 SIP experienced a failure. Refer to Chapter 7, “Troubleshooting the Installation” for SIP and SPA troubleshooting information. The SIP is active and operating normally. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 2-11 OL-13838-02...

  • Page 22: Cisco 10000 Sip-600 Physical Specifications

    10.0 lb (4.6 kg) Operating temperature 41 to 104°F (5 to 40°C) Relative humidity Operating—10 to 90 percent, noncondensing Storage—5 to 95% Storage temperature –4 to 149°F (–20 to 65°C) Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 2-12 OL-13838-02...

  • Page 23: Bandwidth Oversubscription

    2-Port Channelized OC-12/DS0 SPA, page 3-31 Bandwidth Oversubscription On a Cisco 10000 series router running a Performance Routing Engine 4 (PRE4), each half of the chassis comprises four slots and is serviced by a single Nickel 10G Application Specific Integrated Circuit (ASIC) that supports a bandwidth of 11.2 Gbps, as represented in...
  • Page 24 Table 3-1 SPA Bandwidth Capacity Per-Port Bandwidth Number of Ports Total Bandwidth 1-Port 10-Gigabit Ethernet SPA 10 Gbps 10 Gbps 2-Port Gigabit Ethernet SPA 1 Gbps 2 Gbps Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-14 OL-13838-02...

  • Page 25: C H A P T E R 3 Cisco 10000 Series Router Shared Port Adapters

    1.2 Gbps SIP Ingress Oversubscription The Application-Specific Integrated Circuit (ASIC) device for the Cisco 10000 SIP-600 can receive over 40 Gbps of ingress data from the four SPA SPI4.2 interfaces. While the ASIC supports 40 Gbps of ingress memory write bandwidth, the ingress memory read bandwidth on the SIP is the 10 Gbps rate of the SPI4.2 interface to the backplane.

  • Page 26: 1-Port 10-Gigabit Ethernet Spa Overview

    The following sections describe the 1-Port 10-Gigabit Ethernet SPA: • 1-Port 10-Gigabit Ethernet SPA LEDs, page 3-17 • 1-Port 10-Gigabit Ethernet SPA XFP Optical Transceiver Modules, Connectors, and Cables, page 3-17 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-16 OL-13838-02...

  • Page 27: 1-Port 10-Gigabit Ethernet Spa Leds

    • Single-mode intermediate-reach (IR) XFP module—XFP-10GER-OC192IR Cisco Systems qualifies the optics that are approved for use with its SPAs. As of the above-listed small form-factor pluggable (XFPs) are the only optical transceiver modules qualified for use. Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network.
  • Page 28 XFP-10GER-OC192IR: –40 to 185 degrees F (–40 to 85 degrees C) TX power XFP-10GLR-OC192SR: –8.2 to 0.5 dBm XFP-10GER-OC192IR: –4.7 to 4 dBm Receiver sensitivity (maximum) XFP-10GLR-OC192SR: –12.6 dBm XFP-10GER-OC192IR: –14.1 dBm Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-18 OL-13838-02...

  • Page 29: 2-Port Gigabit Ethernet Spa Overview

    2-Port Gigabit Ethernet SPA Faceplate SPA-2X1GE A/L LED (for each interface) STATUS LED (for entire SPA) Two RJ45 (copper) ports The 2-Port Gigabit Ethernet SPA LEDs are described in Table 3-5. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-19 OL-13838-02...
  • Page 30 Contains a Class 1 laser of 850 nm for (1000BASE-SX) 1000BASE-SX (short wavelength) applications. SFP-GE-L Long wavelength/long haul Contains a Class 1 laser of 1310 nm for (1000BASE-LX/LH) 1000BASE-LX/LH (long wavelength) applications. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-20 OL-13838-02...
  • Page 31 802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach 6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-21...

  • Page 32: Sfp Module Cabling And Connection Equipment

    (nm) Fiber Type (micron) (MHz/km) Cable Distance SFP-GE-S 62.5 722 ft (220 m) 62.5 984 ft (300 m) 50.0 1640 ft (500 m) 50.0 1804 ft (550 m) Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-22 OL-13838-02...

  • Page 33: 5-Port Gigabit Ethernet Spa Overview

    The 5-Port Gigabit Ethernet SPA has two types of LEDs: an A/L LED for each individual port and a STATUS LED for the SPA, as shown in Figure 3-6. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-23 OL-13838-02...

  • Page 34: 5-Port Gigabit Ethernet Spa Cables And Connectors

    The SFP module has a receiver port (RX) and a transmitter port (TX) that compose one optical interface. Table 3-10 Table 3-11 provide SFP module information and specifications. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-24 OL-13838-02...
  • Page 35 SFP-GE-S Modules The 1000BASE-SX (short-wavelength) module operates on standard multimode fiber-optic link spans of up to 500 m on 50/125um multimode fiber (MMF) and 300 m on 62.5/125um MMF. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-25 OL-13838-02...
  • Page 36 SFP-GE-Z is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the SFP-GE-Z is 24.9 miles (40 km). Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-26...

  • Page 37: 8-Port Gigabit Ethernet Spa Overview

    The 8-Port Gigabit Ethernet SPA has two types of LEDs: an A/L LED for each individual port and a STATUS LED for the SPA, as shown in Figure 3-7. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-27 OL-13838-02...

  • Page 38: 8-Port Gigabit Ethernet Spa Cables And Connectors

    The SFP module has a receiver port (RX) and a transmitter port (TX) that compose one optical interface. Table 3-14 Table 3-15 provide SFP module information and specifications. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-28 OL-13838-02...
  • Page 39 IEEE 802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach 6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-29...
  • Page 40 1804 ft (550 m) 50.0 1804 ft (550 m) 9/10 — 6.2 miles (10 km) SFP-GE-Z 1550 9/10 — 49.7 miles (80 km) — 62.1 miles (100 km) Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-30 OL-13838-02...

  • Page 41: 2-Port Channelized Oc-12/Ds0 Spa

    LEDs on a SPA. Figure 3-8 2-Port Channelized OC-12/DS0 SPA Faceplate SPA-2XCHOC12/DSO CAR (Carrier/Alarm) LED STATUS LED ACT (Active Loopback) LED Table 3-17 describes the 2-Port Channelized OC-12/DS0 SPA LEDs. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-31 OL-13838-02...

  • Page 42: 2-Port Channelized Oc-12/Ds0 Spa Interface Specifications

    SONET single-mode and multimode optical fiber connection (see Figure 3-9). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 2-Port Channelized OC-12/DS0 SPA supports the following types of optical transceiver modules: Multimode (MM) SFP module—SFP-OC12-MM •...
  • Page 43 2-Port Channelized OC-12/DS0 SPA -equipped routers back to back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-33 OL-13838-02...
  • Page 44 Chapter 3 Cisco 10000 Series Router Shared Port Adapters 2-Port Channelized OC-12/DS0 SPA Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 3-34 OL-13838-02...

  • Page 45: Chapter 4 Preparing To Install A Sip Or A Spa

    Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might harm you. A warning symbol precedes each warning statement. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-35 OL-13838-02...
  • Page 46 üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-36 OL-13838-02...
  • Page 47 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-37 OL-13838-02...
  • Page 48 Chapter 4 Preparing to Install a SIP or a SPA Safety Guidelines Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-38 OL-13838-02...
  • Page 49 Chapter 4 Preparing to Install a SIP or a SPA Safety Guidelines Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-39 OL-13838-02...

  • Page 50: Electrical Equipment Guidelines

    • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-40 OL-13838-02...

  • Page 51: Preventing Electrostatic Discharge Damage

    4-1. The multimode aperture contains a Class 1 LED warning label, as shown in Figure 4-1. These warnings apply to SPAs and SFP modules that transmit signals via an optical carrier signal. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-41 OL-13838-02...
  • Page 52 éstos con instrumentos ópticos. Varning! Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i strålar och titta aldrig direkt på dem med hjälp av optiska instrument. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-42 OL-13838-02...
  • Page 53 ópticos. Advarsel Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte med optiske instrumenter. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-43 OL-13838-02...
  • Page 54 Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments. Statement 1051 Warning Class 1 LED product. Statement 1027 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 4-44 OL-13838-02...

  • Page 55: Chapter 5 Installing And Removing A Sip

    C H A P T E R Installing and Removing a SIP This chapter describes how to install or remove SIPs on a Cisco 10000 series router. This chapter contains the following sections: Handling SIPs, page 5-45 • Online Insertion and Removal of a SIP, page 5-46 •...

  • Page 56: Online Insertion And Removal Of A Sip

    Handling a Cisco 10000 SIP-600 CI SC O 10 00 0 The Cisco 10000 SIP-600 weighs 10 lb (4.6 kg). Always use two hands when handling the SIP. Caution Online Insertion and Removal of a SIP The Cisco 10000 series router supports online insertion and removal (OIR) of the SPA interface processor (SIP) and of the shared port adapters (SPAs).

  • Page 57: Deactivating A Sip

    Card idle time 0 days, 3 hours, 3 minutes, 17 seconds Voltage status: EEPROM contents, slot 1/0: Controller Type : 1380 Hardware Revision : 1.0 PCB Part Number : 73-10771-01 Board Revision Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-47 OL-13838-01...
  • Page 58 The Transceiver in slot 1 subslot 1 port 0 is ENABLED. The Transceiver in slot 1 subslot 1 port 1 is ENABLED. The Transceiver in slot 1 subslot 1 port 2 is ENABLED. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-48 OL-13838-01...

  • Page 59: Sip Installation And Removal

    Install or remove only one SIP at a time. Be sure to verify that each SIP is fully installed and secured Caution before installing another SIP. Use of excessive force can damage the router or SIP. Installing a SIP To install a SIP, follow these steps: Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-49 OL-13838-01...
  • Page 60 SIP) and position the SIP in front of the appropriate line card slots. Caution The Cisco 10000 SIP-600 weighs 10 lb (4.6 kg). Use two hands when handling the SIP. Step 4 Carefully align the upper and lower card guides on the SIP with the upper and lower guides in the chassis...
  • Page 61 Simultaneously pivot both SIP ejector levers toward each other (until they are parallel to the faceplate) Step 6 to firmly seat the SIP in the router backplane. See Figure 5-3. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-51 OL-13838-01...

  • Page 62: Removing A Sip

    SIP. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the midplane or backplane with your hand or any metal tool, or you could shock yourself. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-52...
  • Page 63 FA UL T MI SW IR PO W ER FA UL T MI SW IR P R O C E S S O R O N LY Captive screws Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-53 OL-13838-01...
  • Page 64 Touching only the metal card carrier, slide the SIP out of the slot (see Figure 5-6). Place the SIP on an Step 5 antistatic surface, or in an antistatic bag. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-54 OL-13838-01...
  • Page 65 Do not operate the system unless all cards and faceplates are in place. Statement 1029 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-55...
  • Page 66 Chapter 5 Installing and Removing a SIP SIP Installation and Removal Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 5-56 OL-13838-01...

  • Page 67: Handling Spas

    C H A P T E R Installing and Removing a SPA This chapter describes how to install or remove SPAs on the Cisco 10000 series router. This chapter contains the following sections: Handling SPAs, page 6-57 • Online Insertion and Removal of a SPA, page 6-58 •...

  • Page 68: Online Insertion And Removal Of A Spa

    Online Insertion and Removal of a SPA The Cisco 10000 series router supports OIR of a SPA independently of removing the SIP. This means that a SIP can remain installed in the router with one SPA remaining active, while you remove another SPA from one of the SIP subslots.

  • Page 69: Reactivating A Spa

    When you deactivate a SPA, the corresponding interfaces are also deactivated. This means that these interfaces will no longer appear in the output of the show interface command. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 6-59 OL-13838-02...

  • Page 70: Installing A Spa In A Sip

    A particle that partially or completely blocks the core generates strong back reflections, which can cause instability in the laser system. Inspection, cleaning, and reinspection are critical steps to take before making fiber-optic connections. Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 6-60 OL-13838-02...

  • Page 71: Cleaning Optical Devices

    FPD process has been initiated. The upgrade process can take several minutes. Use the show upgrade fpd progress command to obtain information about the FPD process. SIPs or SPAs that undergo an FPD upgrade automatically reboot. Return to Step Cisco 10000 Series Router SIP and SPA Hardware Installation Guide 6-61 OL-13838-02...

  • Page 72: Using Show Commands To Verify Spa Status

    Displays the field-programmable devices (FPD) version router(config)# show hw-module subslot all fpd information of SPAs. Displays the Cisco IOS software version, names and sources of router(config)# show version configuration files, and boot images. router(config)# show interfaces Displays SPA configuration and statistics information.

  • Page 73: Troubleshooting The Installation

    C H A P T E R Troubleshooting the Installation This chapter describes how to troubleshoot the installation of SIPs and SPAs on the Cisco 10000 series router. This chapter contains the following sections: Troubleshooting, page 7-63 • Using debug Commands, page 7-64 •...

  • Page 74: Using Debug Commands

    Security Guidelines” section on page Using debug Commands Along with the other debug commands supported on the Cisco 10000 series router, you can obtain specific debug information for the SIP on the Cisco 10000 series router using the debug hw-module privileged EXEC command.

  • Page 75: Packing A Spa For Shipment

    Use Cisco Systems original packaging for the shipment of all SPAs and cable-management brackets. Caution Failure to properly use Cisco Systems packaging can result in damage or loss of product. During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly Warning touch the backplane with your hand or any metal tool, or you could shock yourself.
  • Page 76 Troubleshooting the Installation Packing a SIP for Shipment • Two foam packing cushions Use Cisco Systems original packaging for the shipment of all SIPs. Failure to properly use Cisco Caution Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card.
  • Page 77 SIPs and SPAs must have the right FPD version to function properly; an FPD incompatibility will disable all interfaces on the SPA or all SPAs within the SIP. An FPD image package is used to upgrade FPD images. Whenever a Cisco IOS image is released that FPD image package supports SPAs, a companion SPA FPD image package is also released for that Cisco IOS software release.
  • Page 78 The SPA provides the interface between the network and the SIP. Secondary slot on a SIP where a SPA is installed. The primary slot is the chassis slot on the router. subslot Cisco 10000 Series Router SIP and SPA Hardware Installation Guide GL-2 OL-13838-01...

  • Page 79: I N D E X

    2-10 blank filler plate interface processor for empty subslots in a SIP tools and parts required for installation 4-35 single-height size intermediate reach SFP optical transceiver module 3-32 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide IN-1 OL-13838-02...
  • Page 80 SFP-GE-Z 3-22, 3-26, 3-29, 3-30 optics modules SFP module qualified for SPAs (table) cabling 3-26, 3-30 organization, document 1-viii SFP-OC12-IR1 3-32 SFP-OC12-LR1 3-32 SFP-OC12-MM 3-32 SFP-OC12-SR 3-32 Cisco 10000 Series Router SIP and SPA Hardware Installation Guide IN-2 OL-13838-02...
  • Page 81 SPA (shared port adapter) definition interfaces optics compatibility (table) SPA (shared port adapter) SPA 4-35 storage temperature 2-12 subslot numbers, on SIP 2-10 subslots temperature 2-12 transceivers translated documentation 1-ix Cisco 10000 Series Router SIP and SPA Hardware Installation Guide IN-3 OL-13838-02...
  • Page 82 Index Cisco 10000 Series Router SIP and SPA Hardware Installation Guide IN-4 OL-13838-02...

Table of Contents