Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell MDENR100
Summary of Contents for Honeywell MDENR100
- Page 1 MDENR100/HBENR100 MDENR100/HBENR100 MDENR100/HBENR100 MDENR100/HBENR100 Cable / DSL Router Cable / DSL Router Cable / DSL Router Cable / DSL Router Installation Guide Installation Guide Installation Guide Installation Guide CSMDENR100V1 12/04 Rev. A...
-
Page 2: Ce Mark Warning
The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors, which may appear in this guide. Ethernet is a trademark of XEROX Corporation. Microsoft, Windows and Windows logo are trademarks of Microsoft Corporation. No Part of the contents of this guide maybe transmitted or reproduced in any form or by any means without the written permission of the manufacturer. -
Page 3: Table Of Contents
Table of Contents Introduction ...............................1 Before You Start.............................1 System Requirement .............................1 How to Use this Guide...........................1 2: Hardware Installation ............................2 Product Descriptions .............................2 2.1.1 Overview ................................2 2.1.2 Features .................................2 2.1.3 LEDs and Reset Button ..........................2 Installing the Router ............................3 2.2.1 Preparing for the installation..........................7 2.2.2 Getting Started...............................7... - Page 4 Setup the Advanced Features ........................21 3.5.1 LAN IP Setting............................. 21 3.5.2 DHCP Setting.............................. 22 3.5.3 Firewall Setting ............................23 3.5.4 Privilege ..............................24 3.5.5 Virtual Servers............................. 24 3.5.6 Routing................................ 26 3.5.7 WAN MAC Address............................. 27 3.5.8 DDNS Setting.............................. 28 3.5.9 MAC Control ...............................
-
Page 5: 1: Introduction
1: Introduction As a gateway router with four-port fast Ethernet switch, the Cable/DSL Gateway Router provides a cost-effective solution to sharing the network resource for Home and Small Business. The Cable/DSL Gateway Router allows you to connect with Cable or DSL Modems. The built-in NAT technology delivers a firewall protection to prevent any intrusion from outsiders. -
Page 6: 2: Hardware Installation
2: Hardware Installation 2.1 Product Description This chapter describes the features and functions of the router and shows how to physically install it. 2.1.1 Overview Combined with 4 dual speed Fast Ethernet ports, the Cable/DSL Gateway Router perfectly meet cost-effective need of Home and Small Business. -
Page 7: Installing The Router
2.2 Installing the Router This section will discuss what you should do before connecting your router to the network and how to physically install it. The MDENR100 Cable/DSL Router fits into Quicknetwork panels. The HBENR100 Cable/DSL Router fits into SuperPro panels. - Page 8 To install the MDENR100 into a QuickNetwork panel, place the unit into the panel and align module into a free 6 inch slot with snap rivets engaged. Once the rivets are aligned with the holes, pull out the plungers and push the module in ½...
- Page 9 The following diagram shows how the unit should be installed in a SuperPro Distribution Panel.
- Page 10 The following diagram shows how the unit should be installed in a QuickNetwork panel.
-
Page 11: Preparing For The Installation
2.2.1 Preparing for Installation Before you start to connect your router to any network device, make sure you get the following values from your ISP. You will need those values to setup the Router and configure you networked PCs to accept the IP address the Router chooses to assign them. -
Page 12: 3: Configuration
3: Configuration 3.1 Configuring the Cable/DSL Gateway Router Once you’ve done with the hardware installation, you may start to configure your system. Note that this high-speed Cable/DSL Router has an internal integrated-circuit chip that programs all the administrative utility. The utility can be accessed by any PC on the network at http://192.168.1.1 . Typing http://192.168.1.1 into the PC’s browser address windows. -
Page 13: Pppoe Connection For Wan
If you use ADSL modem to make broadband access, please go to 3.2.1 PPPoE Connection for WAN. If the fixed IP is used, please go to 3.2.2 Fixed IP for WAN. As for the cable modem, please go to 3.2.4 Dynamic IP for WAN. Figure 3-3 The “Home”... - Page 14 Figure 3-4 Cable/DSL Setup Menu Screen Figure 3-5 Cable/DSL Setup Menu with “No” Option Screen -10-...
-
Page 15: Fixed Ip For Wan
Figure 3-6 PPPoE Menu Screen 3.2.2 Fixed IP for WAN If your ISP has assigned your home a static IP address (See Appendix A Static and Dynamic IP Address), you may connect to the Internet by using a fixed, or static address. To set up a Fixed IP for WAN, do the following steps as an example. -
Page 16: Pptp For Wan
Figure 3-7 Cable/DSL Setup Menu Step 3 Enter the DNS Address. (See Figure 3-8 DNS Menu Screen) Your ISP should provide you with at least one DNS IP Address. If not, contact your ISP. Figure 3-8 DNS Menu Screen 3.2.3 PPTP For WAN Step 1 Choose “YES”... - Page 17 Figure 3-9 Cable/DSL Menu Step 2 Click “Next>>”, and then the following screen will appear. Enter the information of “PPTP Account”, “PPTP Password”, and “Host Name”. “My IP Address” and ”My Subnet Mask” assigned by your Internet Service Provider should be filled in. Figure 3-10 PPTP Settings Screen -13-...
-
Page 18: Dynamic Ip For Wan
3.2.4 Dynamic IP for WAN If you did not receive any values such as fixed IP address, Subnet Mask, Default Gateway and Primary DNS IP address from your ISP, choose the “NO” option in both Figure 3-4 Cable/DSL Setup Menu Screen and Figure 3-8 DNS Menu Screen. -
Page 19: Time Zone
Figure 3-12 DNS 3.2.7 Time You can get the data of log files by setting the time zone. (See figure3-13 Time Zone) Figure 3-13 Time Zone 3.3 Browsing the Status 3.3.1 Status This screen provides the current information of the device. All of the information provided is read-only. (See Figure 3-14 Status Menu Screen) Router Name: You will see the name of this device in this field. -
Page 20: Dhcp Table
LAN: These fields display the current IP address and Subnet Mask of the router as seen by the users on your internal network. WAN: These fields display the IP Address, Subnet Mask and Default Gateway of the router as seen by external users on the Internet. -
Page 21: Routing Table
Figure 3-15 DHCP Table Screen 3.3.3 Routing Table You will see the current routing configuration such as the address of Destination LAN IP, Default Gateway, Subnet Mask, Metric and the Interface (LAN or WAN). See Figure 3-16 Routing Table Menu Screen Figure 3-16 Routing Table Menu Screen 3.3.4 DDNS Status Screen This router supports the DDNS service allowing you to use one specific DNS name while the actual IP address... -
Page 22: Viewing The Tools
Figure 3-17 DDNS Status Screen 3.4 Viewing the Tools 3.4.1 System Log You can acquire the information of the system in this screen, including the time, the type and the message. Figure 3-18 System Log 3.4.2 Hacker Log You can detect the intrusion from this screen. This screen shows the information of the unauthorized access request to your network. -
Page 23: Incoming Access Log
Figure 3-19 Hacker Log Menu Screen 3.4.3 Incoming Access Log The screen shows the log that records the packet, which comes from WAN. You can see the source IP and it’s port number in this screen. Figure 3-20 Incoming Access Log 3.4.4 Outgoing Access Log The screen shows the log that records the packet, which comes from WAN and sends to the destination. -
Page 24: Reset
3.4.5 Reset You have two options to reset your Router. If you choose “Restart”, the router will reboot yet retain all the previous configuration settings. On the other hand, if you choose “Restore Factory Settings”, the Router will remove all the previous settings and go back to the factory state. (See Figure 3-22 Reset Menu Screen) For more information about “Reset”, see Caution: Reset Button. -
Page 25: Setup The Advanced Features
Figure 3-24 Backup Menu Screen 3.5 Setup the Advanced Features Once you’ve configured the basic settings discussed in section 3.2, you may move to the settings of Advanced Features. In this section, we’ll explain the setting of LAN IP, DHCP, Firewall, Privilege, Virtual Servers and the Routing. -
Page 26: Dhcp Setting
3.5.2 DHCP Setting A DHCP (Dynamic Host Configuration Protocol) Server automatically assigns IP address to each computer on your network. Unless you already have one, it is highly recommended that your router be set up as a DHCP server. Figure 3-26 shows the DHCP Setting screen. Simply fill out the values of each entry and click the “Apply” button. -
Page 27: Firewall Setting
3.5.3 Firewall Setting Remote Management makes you able to manage the router from Internet. NAT allows all of the computers on your network to use one IP address. Hacker Attack Protect keeps your network away from hacker attacking. Block Hacker Scan is used to hide the router so that the hackers won’t find it on the network. UPnP Services enables the connections between UPnP Services and PC automatically. -
Page 28: Privilege
desired IP address number in the blank of the LAN IP. 3.5.4 Privilege Privilege setting allows you to keep certain PCs on your network from accessing to the Internet. You can set up a filter through an IP address or network port number. Users who have their IP address or Port number listed on the “Blocked Private Address”... - Page 29 Figure 3-30 Virtual Server Setting Menu Screen Figure 3-31 Virtual Server Setting Menu Screen Application to Configure: You can choose one of 10 applications to configure. Name: Enter the desired name in the column. Status: Choose Enabled to enable it or Disabled to ignore. IP Address: Set IP addresses to be detected by users.
-
Page 30: Routing
Figure 3-32 Virtual Server Setting Menu Screen (With WAN Address) 3.5.6 Routing Static Routing: You may set up a static route if your want to connect your router to more than one network. A static route is a pre-determined pathway that network information must travel to reach a specific host or network. Figure 3-30 shows the screen of Static Routing and Dynamic Routing menu. -
Page 31: Wan Mac Address
Dynamic Routing: Dynamic Routing can be used to cache routes learned by routing protocols, thus allowing the automation of static routing maintenance. The router, using the RIP protocol, determines the network packet’s route based on the fewest number of hops between the source and the destination. In this case, you could automatically adjust to physical changes in the network’s layout. -
Page 32: Ddns Setting
Figure 3-34 WAN MAC Address Setting 3.5.8 DDNS Setting Setting the Dynamic DNS allows others to access your FTP or Web service on your computer using DNS-like address. DDNS Status Choose Enabled to enable it or Disabled to ignore. Retry Time: It allows the router to make the connection again in the period you set. DDNS Server: Choose the desired server from the drop down list. -
Page 33: Mac Control
3.5.9 MAC Control This feature allows you to block certain specific PCs accessing your ISP. Figure 3-36 MAC Control Screen 3.5.10 URL Blocking The function provides filtering mechanism to prevent user access several specific websites. Figure 3-37 URL Blocking 3.5.11 Port Forwarding The function allows Internet Users to access Services on your LAN. -
Page 34: Special Applications
Figure 3-38 Port Forwarding 3.5.12 Special Applications Users are allowed to define the application as a “Special Application” to enable the specific traffic to come into LAN side. Figure 3-39 Special Applications 3.5.13 Time Filter The function allows you to filter client connect to Internet via time. -30-... -
Page 35: Configuring Your Pcs To Connect To The Router
Figure 3-40 Time Filter 3.6 Configuring your PCs to Connect to the Router Before you start to configure other PCs to accept the IP address that your Router will provide, make sure the network card or adapter has been successfully installed into each PC you planed to connect to the Router. Complete the following steps to configure your PC: Step 1 Click the Start button, select Setting, then Control Panel. - Page 36 Step 5 Click Properties button, then choose IP Address tab. Select Obtain an IP address automatically. Press OK. You have completed the client settings. (See Figure 3-42) Note: Windows may ask you for original Windows installation files, supply them as needed. Figure 3-42 TCP/IP Properties -32-...
-
Page 37: 4: Specifications
4: Specifications 4.1 Technical Specifications Standards IEEE 802.3, IEEE 802.3u CSMA/CD, PPPoE, PPP, PPTP Client, ARP, DHCP Client and Server, Protocol TCP/IP, UDP, ICMP, RIP1/RIP2, DNS Proxy, Dynamic DNS, SNTP Four 10/100 Mbps LAN ports (1 Uplink port shared) Ports 10/100 Mbps WAN port Connector RJ-45 connector... - Page 38 conditioning, generators, and radio signals. STP is also used for wiring outdoors. There are two types of the wiring: Straight-Through Cables and Crossover Cables. Category 5 UTP/STP cable has eight wires inside the sheath. The wires form four pairs. Straight-Through Cables has same pinouts at both ends while Crossover Cables has a different pin arrangement at each end.
-
Page 39: Appendix A - Static And Dynamic Ip Address
Appendix A: Static and Dynamic IP Address A static IP address is an IP address that is assigned to a computer by an Internet service provider to be its permanent address on the Internet. It is normally used in the computer networks, where computers are connected all the times. -
Page 40: Limited Warranty
Limited Warranty or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. Connection of any device(s) to a communicating bus of a Honeywell security system (e.g., keypad bus, polling loop) other than those manufactured or approved by Honeywell shall void this warranty.