Hitachi GR2000 Series Configuration Commands page 459

Table 5-8
Can not set replace_user_priority because
penalty_dscp is already defined.
Can not set replace_user_priority because
penalty_tos or penalty_dscp is already
defined.
Can not set replace_user_priority because
replace_exp is already defined.
Can not set replace_user_priority because
tos_map or dscp_map is already defined.
Can not set replace_user_priority because
upc or min_rate or max_rate is already
defined.
Can not set same min_rate and max_rate
value in one flow list configuration.
Can not set scan_extension.
Can not set scan_extension because forward
or drop not specified.
Can not set scan_extension because protocol
ip not specified.
Can not set tcp protocol.
Can not set these parametors(replace_tos,
replace_dscp, tos_map, dscp_map,
replace_exp) in the same flow list
configuration.
Can not set tos_map or dscp_map because
priority or discard is already defined.
Can not set tos_map or dscp_map because
replace_exp is already defined.
Can not set tos_map or dscp_map because
replace_tos or replace_dscp is already
defined.
Can not set tos_map or dscp_map because
replace_user_priority is already defined.
Can not set udp protocol.
GR2K-GA-0014
Ver. 07-02
Flow Information Error Messages (continued)
It is not possible to set the VLAN priority rewrite value because the
contract bandwidth violation dscp rewrite value is defined. Delete the
contract bandwidth violation dscp rewrite value in order to set the
VLAN priority rewrite value.
It is not possible to set the VLAN priority rewrite value because the
contract bandwidth violation tos rewrite value or the contract
bandwidth violation dscp rewrite value is defined. Delete the contract
bandwidth violation tos rewrite value or the contract bandwidth
violation dscp rewrite value in order to set the VLAN priority rewrite
value.
It is not possible to set the VLAN priority rewrite value because the
exp field rewrite value is defined. Delete the exp field rewrite value in
order to set the VLAN priority rewrite value.
It is not possible to set the VLAN priority rewrite value because
"tos_map" or "dscp_map" is defined. Delete "tos_map" or
"dscp_map" in order to set the VLAN priority rewrite value.
It is not possible to set the VLAN priority rewrite value because
bandwidth setting or minimum bandwidth guarantee and maximum
bandwidth limit are defined. Delete bandwidth setting or minimum
bandwidth guarantee and maximum bandwidth limit in order to set
the VLAN priority rewrite value.
No setting is possible because the minimum band assurance value is
greater than or equivalent to that of the maximum band restriction.
For the minimum band assurance, specify a value smaller than the
maximum band restriction.
In a flow filter, an S/W search flag cannot be set when the list number
is in the range of 1 to 20000. Specify the S/W search flag when the
list number is in the range of 40001 to 60000.
An S/W search flag cannot be set simultaneously with parameters
other than forward or drop.
An S/W search flag cannot be set because ip is not specified in the
upper protocol. To set an S/W search flag, specify ip in the upper
protocol.
In specifying the high-order protocol, 6(tcp) cannot be specified.
Specify the "tcp" by using the packet flow detecting conditions.
The tos rewriting value, dscp rewriting value, and tos_map,
dscp_map, and exp field rewriting values cannot be set
simultaneously. Specify them individually.
tos_map or dscp_map cannot be set because the output priority or
queuing priority has been defined. To set the tos_map or dscp_map,
delete the output priority or queuing priority.
tos_map or dscp_map cannot be set because the exp field rewrite
value has been defined. To set the tos_map or dscp_map, delete the
exp field rewrite value.
tos_map or dscp_map cannot be set because the tos rewriting value
or dscp rewriting value has been defined. To set the tos_map or
dscp_map, delete the tos rewriting value or dscp rewriting value.
It is not possible to set "tos_map" or "dscp_map" because the VLAN
priority rewrite value is defined. Delete the VLAN priority rewrite
value in order to set "tos_map" or "dscp_map".
In specifying the high-order protocol, 17(udp) cannot be specified.
Specify the "udp" by using the packet flow detecting conditions.
Configuration Error Messages
5-69