Hitachi GR2000 Series Configuration Commands page 431

Table 5-5
ospf: invalid retransmit-interval value at
<Value> not in range 1 to 65535
ospf: invalid router-dead-interval value at
<Value> not in range 1 to 65535
ospf: invalid seconds value at <Value> not in
range 0 to 4294967295
ospf: invalid transit-delay value at <Value> not
in range 1 to 65535
ospf: invalid vpn number value at <Value> not
in range 1 to <Max_Value>
ospf: key id must be between 0 and 255
ospf: keys cannot have same start time
ospf: mask not contiguous
ospf: minute must be between 0 and 59
ospf: month must be between 1 and 12
ospf: multipath option not valid for vpn route
ospf: neighbor-id must be an IP address
ospf: net range already specified
ospf: Non-masked bits not zero for <Address>
masklen <Masklen>
ospf: Non-masked bits not zero for <Address>
mask <Mask>
ospf: nssa option not valid for backbone
ospf: out of range
ospf: Router ID not defined
ospf: secondary auth was overwritten by md5
for virtual link to <Neighbor ID> in Domain
<Domain ID> [on VPN <VPN ID>].
ospf: stop accept time must be later than start
accept time
GR2K-GA-0014
Ver. 07-02
Routing Protocol Error Messages (continued)
In the OSPF area definition, the retransmit-interval value is out of the
valid range. Specify a value within the range of 1 to 65535.
<Value>: Specified retransmit-interval value
In the OSPF definition, the router-dead-interval value is out of valid
range. Specify a value within the range of 1 to 65535.
<Value>: Specified router-dead-interval value
Specified timer value is invalid.
Specify a value within the range of 0 to 4294967295.
<Value>: Specified timer value
In the OSPF definition, the transit-delay value is out of valid range.
Specify a value within the range of 1 to 65535.
<Value>: Specified transit-delay value
The range of VPN value is invalid. Specify a value within the range of
1 to <Max_Value>.
<Value>: Specified VPN number
<Max_Value>: Maximum VPN number
Specified MD5 authentication key ID is invalid. Specify a value within
the range of 0 to 255.
MD5 authentication message digest generation start time is
duplicated. Do not duplicate the start time.
Bit 1 of the specified mask does not continue. Use a mask where bit
1 continues.
Specified time (minute) is invalid. Specify a value within the range of
0 to 59.
Specified month is invalid. Specify a value within the range of 1 to 12.
The Multipath option is defined for VPN. VPN does not support
multipath option.
The IP address defined to neighborhood is invalid. Specify in IP
address format.
Network parameter is already specified in OSPF area definition.
Do not duplicate a networks parameter.
In masklen, 1 is specified for non-masked bit of the specified
address. Set non-masked bit 0.
<Address>: Specified address
<Masklen>: Specified mask length
In mask, 1 is specified for non-masked bit of specified address.
Specify 0 to non-masked bit 0.
<Address>: Specified Address
<Mask>: Specified mask
Nssa option is defined in a backbone area. Do not defined a nssa
option in a backbone area.
The parameter-specified range is exceeded in the input command
syntax. Numeric values of more than 4294967296 are contained.
Reconfirm a parameter.
Router ID is not defined. Specify the Router ID.
In a specified virtual link, both MD5 authentication and the 2nd
authentication key are defined. Delete the unnecessary
authentication method.
<Neighbor ID>: router ID of the adjacent OSPF virtual link router
<Domain ID>: specified domain No. of the OSPF virtual link
<VPN ID>: specified VPN No. of the OSPF virtual link.
MD5 authentication message digest accept end time is earlier than
start time. Set the value so start time is earlier than end time.
Configuration Error Messages
5-41