NAD C 546BEE Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. CD Player
  5. C 546BEE
  6. Owner's manual

NAD C 546BEE Owner's Manual

Hide thumbs Also See for C 546BEE:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
C 546BEE
®
Compact Disc Player
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for NAD C 546BEE

Summary of Contents for NAD C 546BEE

  • Page 1 C 546BEE ® Compact Disc Player Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 14 Outdoor Antenna Grounding - If an outside antenna or cable system SAVE THESE INSTRUCTIONS FOR LATER USE. is connected to the product, be sure the antenna or cable system is FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE grounded so as to provide some protection against voltage surges AUDIO EQUIPMENT.
  • Page 3 FULLY INSERT. AC RECEPTACLE. CAUTION The C 546BEE employs a Laser System. To ensure proper use of this product, THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY ACCESSIBLE. please read this owner’s manual carefully and retain for future reference.
  • Page 4 RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT) the negative impact of batteries and waste batteries on the environment The model and serial number of your new C 546BEE are located on the is minimized, thus contributing to the protection, preservation and quality back of the cabinet.

  • Page 5: Table Of Contents

    USING THE C 546BEE – CD MODE ....... . 11...

  • Page 6: Introduction

    If the Press [STOP/OPEN] if you want to end play and reset the pickup to the C 546BEE is placed in close proximity to a radio tuner (AM or FM), a VCR or beginning of the disc.

  • Page 7: Identification Of Controls

    WMA/MP3 files, the display will revert to total number of files. If the C 546BEE was If the disc tray is open and the Standby button is pressed, the disc tray programmed to play a selection of tracks, the program will be retained will draw close and the C 546BEE goes to standby mode.
  • Page 8 CD or other compatible media disc. Press to start play or resume play after Pause. The icon “ ” is illuminated in the VFD indicating the C 546BEE is in playback mode. If the disc tray is open, press this button INFORMATION AUDIO CD...

  • Page 9: Rear Panel

    Mains cable. Before connecting the cable to a live wall socket ensure that receiver, computer soundcard or other digital processors. it is firmly connected to the C 546BEE’ s AC Mains input socket first. Always disconnect the AC Mains cable plug from the live wall socket first, before 3 +12V TRIGGER IN: This input allows the C 546BEE to be switched disconnecting the cable from the C 546BEE’...

  • Page 10: Cd 9 Remote Control

    IDENTIFICATION OF CONTROLS CD 9 REMOTE CONTROL ON: Switch ON C 546BEE. OFF: Switch OFF C 546BEE. CD: Select CD as the active source. USB: Select USB as the active source. RAND: Play tracks/files in random mode. OPT: Select optical input as the active source.

  • Page 11: Operation

    When programming a sequence of tracks, the program is being played. During Program Play, the SKIP buttons will C 546BEE must be in STOP mode. Using the CD 9 remote control, enter your access only the tracks in the program list.

  • Page 12: Using The C 546Bee - Usb Mode

    OPERATION USING THE C 546BEE – USB MODE The C 546BEE can play back MP3/WMA files stored in external USB (Universal Serial Bus) devices. The following are the C 546BEE’s capabilities with respect to USB device playability. USB SUPPLEMENTARY INFORMATION...

  • Page 13: Using The C 546Bee - Cd 9 Remote Control

    OPERATION USING THE C 546BEE – CD 9 REMOTE CONTROL The CD 9 remote control is provided with your C 546BEE Compact Disc Player to enable you to operate playback functions from the comfort of your chair or from virtually anywhere in the room. For reliable operation, there should be a clear line-of-sight path from the remote control to the front of the CD player.

  • Page 14: Reference

    • Turn on the equipment connected with the the audio cable is turned off. audio cable. Sound skips. • The C 546BEE is subject to vibration or physical • Change the installation location. shock from external sources. The C 546BEE cannot be switched to • A mono plug is plugged-in at the +12V...

  • Page 15: Specifications

    Specifications are subject to change without notice. For updated ±0.05 dB (ref. 0dB 1 kHz at -20 dB) documentation and features, please log onto www.NADelectronics.com for ±0.15 dB (ref. 0dB 1 kHz at -60 dB) the latest information about C 546BEE. Standby power <0.5W...
  • Page 16 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents